ID1 Max. Bore Max. Bore Weight Size Standard Shallow L FL P SL OD T HD OAL G R Flange Keyway Keyway mm mm mm mm mm mm mm UNC mm mm mm mm kg 5S 30.18 31.75 34.04 14.99 11.43 7.37 82.55 1/4 - 20 47.75 71.37 19.05 24.68 0.499 6S 36.53 38.10 41.66 19.81 13.46 7.36 101.60 5/16 - 18 63.50 88.90 22.35 27.69 0.862 - 44.45 41.66 19.81 13.46 - 101.60 - 63.50 88.90 22.35 27.69 0.816 7S 41.28 47.63 46.74 19.81 17.53 8.89 117.48 3/8 - 16 71.37 100.08 25.40 33.27 1.179 8S 49.23 57.15 53.34 22.35 19.05 9.65 138.43 3/8 - 16 82.55 111.51 28.70 38.10 1.996 - 60.33 49.28 22.35 26.16 - 138.43 - 82.55 125.73 28.70 38.10 1.678 9S 60.33 63.50 61.21 26.16 19.81 10.41 161.29 1/2 - 13 92.20 128.52 36.58 44.45 2.948 - 73.03 57.91 26.16 31.75 - 161.29 - 104.90 152.40 36.58 44.45 2.812 10S 69.85 79.38 68.58 30.99 20.57 10.41 190.50 1/2 - 13 111.25 144.53 41.40 50.8 4.763 - 85.73 68.58 30.99 20.57 - 190.50 - 120.65 144.53 41.40 50.8 4.445 11S 85.73 92.08 87.38 38.10 28.70 14.22 219.08 1/2 - 13 133.35 181.10 47.75 60.45 7.530 - 98.43 77.72 38.10 39.62 - 219.08 - 143.00 203.20 47.75 60.45 7.439 12S 73.03 - 101.60 42.93 32.51 16.00 254.00 1/2 - 13 123.95 209.55 58.67 68.33 12.474 98.43 100.03 101.60 42.93 32.51 - 254.00 - 146.05 209.55 58.67 68.33 12.066 13S 114.30 - 111.25 50.04 33.27 20.57 298.45 5/8 - 11 171.45 234.95 68.33 77.72 20.412 14S 127.00 - 114.30 57.15 26.92 15.75 352.43 5/8 - 11 190.50 250.95 82.55 88.90 31.298 16S 139.70 152.40 152.40 69.85 50.80 25.40 479.43 5/8 - 11 203.20 368.30 120.65 107.95 56.699 Mechanical Power Transmission S-Flex Couplings Dimensional Data 16 www.jbj.co.uk/s-flex-couplings.html Note Spacing between shafts should be greater than 3.175mm and less than OAL minus the sum of the two bore dimensions. See page 9 for Performance Data. The sizes with two dimensions listed indicate measurements for standard flanges (1st Line) and modified spacer flanges (2nd Line). See page 20. To determine shaft separation (BSE, use the formula BSE = OAL - (2 x L). Dimensions Millimetres S Type Flanges » S flanges are made of high strength cast iron and are bored to size for a slip fit on standard shafts. » S flanges are easy to install, are readily available from stock in a wide range of popular bore sizes, and are supplied with two set screws at 90°. S Type Couplings » S Type couplings, normally supplied with the two-piece E sleeve, can be used with any JE, JN, N, H, or HS sleeves. #DriveLineHarmony
RkJQdWJsaXNoZXIy NzQyNjQ=