PUMP DRIVE COMPONENTS 11 24
When your coupling element should look like this but actually looks like this you can size the element using our chart with just a fraction of the original coupling If you require a coupling other than a spider type or gear type coupling there are a range of criteria ( ) in specifying the most suitable coupling for your application but link to selection table we will guide you all the way to obtain the right coupling for power transmission. For assistance please telephone the jbj Techniques technical office: 01737 767493 or email: info@jbj.co.uk » » ® patented Elika profile is everything 01737 767493 info@jbj.co.uk www.jbj.co.uk quality products for mechanical & fluid power - registered in England No: 1185469 - jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/E requirements an excellence in engineering You Tube www.jbj.co.uk/ .html couplingelementchart Coupling Element Size Selection Chart Telephone: 01737 767493 or fill in for a complimentary chart. this form Coupling Element Size Comparison Chart (up to Spidex S/CJ125 & Dentex B80) Simply size your coupling, decide the shore hardness colour and contact us immediately. This ‘Pump Drive Component’ catalogue provides technical specifications, power, torque, speeds & other selection data.
Backlash explanation ................................................................................................................................................................................................................................................................................................................................................................................ Petrol engine adaptors ................................................................................................................................................................................................................................................................................................................................................................................ 52 - 54 Page Anti-vibration / noise reduction components ............................................................................................................................................................................................................................................................................................................ 1 - 3 Spidex couplings ................................................................................................................................................................................................................................................................................................................................................................................................ 4 - 10 CJ series couplings ........................................................................................................................................................................................................................................................................................................................................................................................ 11 - 17 G series couplings ........................................................................................................................................................................................................................................................................................................................................................................................... 18 - 21 ® Spidex non backlash coupling .................................................................................................................................................................................................................................................................................................................................................... 22 - 25 ® Dentex couplings ............................................................................................................................................................................................................................................................................................................................................................................................ 26 - 30 Dentex "fl" engine drive couplings ........................................................................................................................................................................................................................................................................................................................................... 31 - 33 Splined bushes ..................................................................................................................................................................................................................................................................................................................................................................................................... 34 L series bellhousings ................................................................................................................................................................................................................................................................................................................................................................................... 35 - 36 RV series bellhousings ............................................................................................................................................................................................................................................................................................................................................................................. 37 - 39 Module 3 bellhousings ............................................................................................................................................................................................................................................................................................................................................................................... 40 - 42 Popular pump flange details ............................................................................................................................................................................................................................................................................................................................................................. 43 Popular machining codes ...................................................................................................................................................................................................................................................................................................................................................................... 44 Cooler bellhousings series KPV .................................................................................................................................................................................................................................................................................................................................................. 45 - 47 P series foot brackets ................................................................................................................................................................................................................................................................................................................................................................................. 48 PTFL & PTFS foot brackets ............................................................................................................................................................................................................................................................................................................................................................. 49 Foot brackets/mounting plates .................................................................................................................................................................................................................................................................................................................................................... 50 - 51 CONTENTS The details contained within this catalogue are reproduced in accordance with the latest information at publication of this catalogue. Errors and Omissions Excepted Last update: 11/12/2024 Pump Drive Components 55 Ultra temperature coupling elements .................................................................................................................................................................................................................................................................................................................................... 56
#DriveLineHarmony www.jbj.co.uk/dampers.html Pump Drive Components Anti-Vibration/Noise Reduction Mountings Damping Rods For MDL 80, 90S, 90L remove grey shaded area. _ 1
#DriveLineHarmony www.jbj.co.uk/dampers.html 2 Damping flanges For use in combination with Raja bellhousings between electric motor and hydraulic pump. They consist of two aluminium parts which are connected by a rubber coat (Nitrile) without any metal connection. o o They are resistant against mineral oils and suitable for working temperatures up to +80 C, for short time +100 C. The possible noise reduction will be approx. 3 - 8 db(A). Damping flanges are available in two degrees of hardness with the description N - normal / H - hard. Pump Drive Components Anti-Vibration/Noise Reduction Mountings for noise reduction of hydraulic power units For bellhousings damped according to VDMA 24561 use type B. For maximum load contact: jbj Techniques Limited technical office, telephone: 01737 767493 or email: info@jbj.co.uk
Damping rings For use when vertical mounting (VI-construction) between bellhousing and tank lid or horizontal (B5-construction) mounting position between motor and bellhousing flange. They consist of two reinforced aluminium rings which are connected by a rubber coat without any metal connection. The used materials (Nitrile) are resistant o against mineral oils and suitable for working temperatures up to +80 C. Pump Drive Components The possible noise reduction will be approx. 3 - 5 db(A). Anti-Vibration/Noise Reduction Mountings for noise reduction of hydraulic power units For maximum load contactj:b j Techniques Limited technical office, telephone: 01737 767493 or email: info@jbj.co.uk Permissible radial weight and bending loads with an operating temperature of + 60°C F>F +F Mb > F x L1 - F x L2 zul. pump motor zul. motor pump 3 #DriveLineHarmony www.jbj.co.uk/dampers.html
4 #DriveLineHarmony www.jbj.co.uk/couplings.html Pump Drive Components ® Introduction to the Spidex Coupling Spidex couplings are torsional flexible shaft couplings, the operating characteristics of which are two hubs with concave claws, transmitting the torque by meshing with an elastic involute gear ring. The coupling concept gives a reliable, smooth power transmission without torsional oscillation and thus protects the connected machines. Due to the complete flexibility and ductility of the elastomer ring, it compensates for parallel and angular displacements as well as to absorb longitudinal movements of the shafts. The involute teeth of the elastomer element are crowned in order to avoid edge pressure on the tooth flanks and thus avoid undesirable axial thrust. The puncture proof coupling can be loaded extremely high since the elastic elements are submitted to compression and not to bending moments of force. The elastomer gear ring, made of a newly developed Simirit-Polyurethane of various degrees of shore hardness, has important advantages in comparison with the standard polyurethanes. It is non-ageing, with resistance against hydrolysis (can be used in tropical conditions), non-abrasive, has a high self-damping effect and is also resistant to oil 0 0 and ozone. It can be used with temperatures ranging from -40 C to +100 C. Spidex couplings can be used for horizontal as well as for vertical shaft connections, for reversing, intermittent service and are electrically insulating. The operating characteristics and the durability of the coupling are very positively influenced by the high overall precision of the machining, especially the claws, unbalance is reduced to a minimum, running is improved and service life considerably increased. Total service factor for K = K1 x K2 x K3 Displacement values Valid for 1500rpm and for a given temperature range -25°C to +30°C. For other speeds and temperature ranges please contact: Dimension E is imperative. Axial displacement Radial displacement Angular displacement
Pump Drive Components Torque Ratings for the ® Spidex Coupling #DriveLineHarmony www.jbj.co.uk/couplings.html 5
Pump Drive Components A/A Hub Combination Standard Coupling Material: Die cast aluminium Material: cast iron = GG; SG iron = GGG; steel = ST; SINT. = Sintered Steel Hub combination A/A H* is the minimum dimension required for the disassembly of the components in the radial direction. Finish bore acc. to ISO standard H7, keyway acc. to DIN 6885, sheet 1 (JS9). Weight and moment of inertia in relation to the materials Al/GG/GGG with max. diameter without keyway. #DriveLineHarmony www.jbj.co.uk/couplings.html 6
Pump Drive Components A/B Hub Combination Standard Coupling Material: Die cast aluminium Material: cast iron = GG; SG iron = GGG; steel = ST & SINT. = Sintered Steel Hub combination A/B H* is the minimum dimension required for the disassembly of the components in the radial direction. Finish bore acc. to ISO standard H7, keyway acc. to DIN 6885, sheet 1 (JS9). Weight and moment of inertia in relation to the materials Al/GG/GGG with max. diameter without keyway. 7 #DriveLineHarmony www.jbj.co.uk/couplings.html
Material: Die cast aluminium Material: cast iron = GG; SG iron = GGG; steel = ST & SINT. * Hubs only available in GGG ** Hubs only available in steel H Pump Drive Components ub combination B/B B/B Hub Combination Standard Coupling * * * ** ** ** H* is the minimum dimension required for the disassembly of the components in the radial direction. Finish bore acc. to ISO standard H7, keyway acc. to DIN 6885, sheet 1 (JS9). Weight and moment of inertia in relation to the materials Al/GG/GGG with max. diameter without keyway. 8 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components ® Hub Designs for the Spidex Coupling 9 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components ® Spidex Special Bores 10 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components CJDB Couplings 11 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components CJSB Couplings Flange is available in steel only. 12 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components CJLFH Couplings Alternative flange machining available on request. Material: SNT, GG, GGG, ST * Hubs only available in GGG ** Hubs only available in steel 13 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components CJSFH Couplings Alternative flange machining available on request. Material: SNT, GG, GGG, ST * Hubs only available in GGG ** Hubs only available in steel 14 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components CJDLF Couplings Alternative flange machining available on request. Material: GG (Cast Iron) 15 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components CJDSF Couplings Flange to flange design available for applications requiring space saving, compact connections. Shaft to flange design is also available for special application situations requiring an alternative connection. 16 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components CJSPC Couplings Hubs available in aluminium, sintered iron and steel. Spacer style features an aluminium spacer piece. Comes with two inserts to increase damping and parallel misalignment capabilities. 2.0 2.5 3.0 3.0 3.5 4.0 4.5 5.0 5.5 2.0 17 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components G Series Coupling Material : Light Alloy Max. Torque = 10 NM Ø 18 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components G Series Coupling Material : Light Alloy Max. Torque = 95 NM Ø 20 e T 19 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components G Series Coupling Material : Light Alloy Max. Torque = 190 NM Ø 20 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components G Series Coupling Material : Light Alloy Max. Torque = 310 NM Ø 21 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Introduction to the Spidex® NBL Coupling The NBL series curved jaw coupling offers zero backlash capability in a 3-piece design. The coupling is provided assembled under preload. The NBL series can be used in a variety of different applications requiring precision and accuracy. The NBL series spider features a straight centre of the spider tooth, providing higher stiffness due to coupling preload. The crowning of the ends of the spider legs allows for misalignment, while the curved jaws and solid spider centre provide high-speed capability. The jaws of the hubs and the spider legs are chamfered to provide easy assembley. The NBL coupling design also allows the blind assembly in tight spaces. Raised spider dots on the legs of the spider ensure proper spacing of the hubs and spider. Proper installation of the coupling can provide isolation of electrical currents. Check the 's' dimension listed on page 24 to ensure the proper spacing between spiders between spiders and hubs. The NBL coupling has spiders available in four different shore hardnesses. Each spider offers benefits for different vibratory, environmental and torque transmission requirements. Elastomer Performance Data for NBL Series Coupling Selection for the NBL Series Typical Applications Measurement and Control Systems The torsional stiffness of the NBL series coupling provides the needed accuracy for measurement and control systems. The low torques of these applications gives the NBL series the ability to provide zero backlash due to the elastomer preload. Servo and Positioning Drives The NBL coupling provides a zero backlash, flexible connection for servo and positioning drives. An added benefit of the NBL series is its damping capabilities. For applications that have vibrations at critical speeds, the NBL coupling can provide a zero backlash solution for vibration problems. 22 #DriveLineHarmony www.jbj.co.uk/couplings.html
Main Spindle Drives The NBL coupling is used in main spindle drives for machine tools. Torque spikes and cyclical loading are handled by the NBL series by damping or by shifting the vibratory frequency range to a non-critical speed range. NBL Series Service Factors Temperature Factor K3 Torsional Stiffness Factor K4 Calculation Formula Shock Load Factors K5 Rated nominal torqu eTn (Nm) = 9550 x P(kW) rpm(1/min) Rotational inertia coefficient (driver) = Moment of inertia (driver) Moment of inertia (driver) + Moment of inertia (driven) Rotational inertia coefficient (driven) = Moment of inertia (driven) Moment of inertia (driver) + Moment of inertia (driven) Check the nominal torque for the application against the rating for the coupling: Tkn > Rated torque of machine x K3 x K4 Peak Torque Shock load (driver side) = Peak torque (driver) x rotational inertia coefficient (driver) x K5 Shock load (driven side) = Peak torque (driven) x rotational inertia coefficient (driven) x K5 Check the peak torque for the application against the rating for the coupling checking both driver and driven sides: Tk Pump Drive Components max > Peak Torque (driver or driven side) x K3 x K4 Spidex® NBL Coupling 23 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Spidex® NBL Coupling NBL NBL NBL The NBL coupling features different hub designs for different applications. Each type offers specific benefits for different types of application. The clamping styles offer the benefit of minimal to zero backlash. 24 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Spidex® NBL Coupling Misalignment The NBL coupling handles the axial, angular and radial misalignment whilst retaining it's zero backlash properties due to its spider design. Axial misalignmen ct an be caused by different shaft tolerances or by thermal expansion of shafts. The NBL series coupling handles axial misalignment while keeping reactionary forces low. Radial misalignmen ctan be defined as a measure of the offset distance between the centrelines of the driving and driven shafts. This type of misalignment causes the highest stress due to the forces involved. Angular misalignmen ctan be defined as a measure of the angle between the centre lines of the driving and driven shafts, where those centre lines would intersect approximately halfway between shaft ends. The NBL coupling can handle a specific amount of angular misalignment for each given size. Refer to table on next page. 25 #DriveLineHarmony www.jbj.co.uk/couplings.html
® The Dentex coupling is a flexible gear coupling whose typical features are two congruent hubs with crowned teeth which transmit torque by meshing with the internal toothing of a housing component. The coupling sleeve with axially parallel involute gearing is centred at the tooth flanks of the coupling hubs. The coupling design meets the requirement to compensate radial, angular, and axial shaft displacements in order to release the neighbouring shaft bearings from non-controlled additional bearing loads. Even with the maximum permissible displacement edge contact of the teeth is excluded and there will be no periodic variation of the angular velocity. The high internal cushioning properties of the plastic material used for the coupling sleeve reduce the effect of shock loading. ® Dentex couplings are as suitable for horizontal shaft connection as they are for vertical connection, for reversing and intermittent service, and they have electrical insulating properties, a low weight, a low flywheel effect and, owing to their compactness, only little space is required for them. The steel/plastic combination also has the advantage that no lubrication by oil or grease is required; the coupling therefore does not need any maintenance. The 6,6-polyamide used for the coupling sleeve excells due to its excellent sliding and wear resistance properties especially with the combination of toughness, hardness and rigidity; it is also resistant to condensation and splash water, engine fuels, oils, greases, alcohols, esters, ketones, aliphatic and aromatic hydrocarbons and many other agents. However, substances of strongly polar character such as concentrated mineral acids, formic acid, cresol, glycol, benzyl alcohol can dissolve 6,6-polyamide at high temperature. Maximum service reliability is guaranteed at temperatures in the range from -25°C to +80°C. It is necessary to use a coupling sleeve in heat stabilised polyamide for temperature up to 140°C. Pump Drive Components ® Introduction to the Dentex Coupling Technical Detail Radial misalignment Angular misaligment Radially angular misalignment 26 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components ® Dentex Couplings for IEC Standard Motors 27 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Standard Dentex® Coupling B Assembly Instructions On assembly it is important that the hubs are correctly fitted on the shafts and that the dimension E is maintained. The dimension E can be controlled by the total assembley length L. An incorrect dimension E has a negative influence on the performance of the coupling. Check the coupling sleeve has minimal axial movement before machine operation. The permissible displacement values depend on rotation and transmitted power. H* is the minimum dimension required for the disengaging of the coupling. Finish bores according to ISO-standard H7, keyway according to DIN 6885, sheet 1 (JS9). Weight and moment of inertia values refer to maximum diameter d without keyway. Steel Nylon 28 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Standard Dentex® Coupling B4R and B3R H* is the minimum dimension required for the disengaging of the coupling. Finish bores according to ISO-standard H7, keyway according to DIN 6885, sheet 1 (JS9). Weight and moment of inertia values refer to maximum diameter d without keyway. B3R with inner and outer circlips B4R with dust seal and circlips H* is the minimum dimension required for the disengaging of the coupling. Finish bores according to ISO-standard H7, keyway according to DIN 6885, sheet 1 (JS9). Weight and moment of inertia values refer to maximum diameter d without keyway. Steel Nylon Steel Nylon 29 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Dentex Special Bores 30 #DriveLineHarmony www.jbj.co.uk/couplings.html
® DENTEX FL couplings are torsionally stiff crowned tooth flange couplings made from a combination of steel and plastic for diesel engine drives. The driving flange is made from glass-fibre reinforced polyamide for high mechanical rigidity and heat resistance. The coupling hub with external crowned teeth is made from steel. ® The Dentex FL coupling allows a keyed connection between diesel engine and hydraulic pump, the pump centred over the SAE housing. ® The application of the Dentex FL coupling results in a non-critical service due to the coupling stiffness. The hazard of a rotating oscillation during the drive will be avoided. If it is not possible to secure the hub by means of end-disc and screw in the case of pump shafts with profiled gear teeth (according to DIN 5480, 5482, SAE), the use of a clamping hub connection should be considered. The radial distortion guarantees a fit on the pump shaft which is free from clearance. Pump Drive Components ® Standard Dentex FL Coupling Typical Layout For A Hydrostatic Pump Direct Coupled To An Engine Flywheel Flywheel Housing Pump Mounting Plate Flywheel Nylon Flange Pump Steel Hub 31 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Metric Flange Details Alternative flange dimensions available on request. d Steel Nylon 32 #DriveLineHarmony www.jbj.co.uk/couplings.html
Minimum Space - The entire length is normally mounted inside the housing face requiring only a flat pump mounting adaptor. The reduced space may result in savings within the equipment frame manufacture or hydraulic costs. Free Axial Travel - Crowned teeth slide freely in the nylon spline with a +/- 2mm axial travel. Any shaft float is absorbed within the coupling and is not transmitted to the pump components. Blind Assembly - Pump hub gear ring fits through the pilot hole of the pump mounting plate resulting in faster assembly at lower cost, therefore requiring no inspection ports or cut outs. Crowned Gear Teeth - Provides for angular misalignment, preventing angular force on the pump shaft bearings and seals. Heat Stable - Fibreglass reinforced nylon designed to operate in diesel engine ambients without air circulation. Dimensionally stable to 120°C. • Available in all hub sizes with parallel bores and metric or SAE splines • Maximum holding power without damage to pump spline. Easy removal • Hub length machined to meet minimum assembly requirements and available space. • Sintered steel hubs for excellent corrosion protection. • Simple, inexpensive, positive clamping. • Requires drilled and tapped pump shaft. • Available for SAE, metric or special splines and straight shafts with keyway. Cross-Bolt Clamping Pump Drive Components Bolt & Washer Clamping FL Couplings 33 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Splined Bushes Material : En24T Also available Japanese JIS D2001 2.5 mod/1.667 mod • Alternative materials on request. • Alternative bush sizes available. • Alternative splines on request. • External splines also available. 34 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components L Series Bellhousing Because of the variety of pumps that our bellhousings cater for the dimensions in the tables apply only to bellhousings with unmachined pump face detail. Details missing are the pump spigot and fixings. Spigots smaller than 'E' dimensions are obtained by the use of steel adaptor rings. 35 #DriveLineHarmony www.jbj.co.uk/couplings.html 70
Pump Drive Components L Series Pump Adaptors L30-OU/000 L25-OU/000 L20-OU/000 Blank Pump Face Adaptors D E 36 #DriveLineHarmony www.jbj.co.uk/couplings.html
For other centre to centre spacing Lx, the permitted weight T can be calculated using the following approximated formula: perm. Fzul.[N] = F[N] + 0.5 F( L(mm) -1) Maximum operating temperature permitted + 80°C, for short periods + 100°C Lx(mm) Monobloc-Bellhousings with noise damper acc. to VDMA 24 561 It’s a well known fact, that manufacturers of hydraulic accessories have no influence at all upon the noise characteristics of a pump. The influencing of airborne, structure borne and liquid sound is incumbent on the pump design engineer himself. The noise characteristics of a pump – consisting of basic frequency and harmonic waves – can become very annoying when the structure borne noise of the hydraulic unit and the integrated elements of the machine are combined. The flow vibration of a pump combined with it’s pressure vibration, can cause a particularly unpleasant resonance of the structure, which in itself cannot always be calculated, even by means of a sound pressure level monitoring in form of a dB(a) value. In order to prevent the reproduction of this vibration into other integrated elements of the structure, it is necessary to isolate the structure borne noise. This is achieved by the use of flexible drive couplings, flexible connections on pipe work and also by the use of bellhousings with integrated noise / vibration reduction flanges. Damping flanges of this type consist of an elastomeric element, which isolates the metallic contact between the pump and other elements of the hydraulic unit. Our associate company, Raja-Lovejoy manufactures and distributes damping flanges for the reduction of noise within hydraulic units. With many years of experience within this field, a monobloc bellhousing system with integrated noise damping has been developed, (top left drawing, page 39), which offers a simples solution against conventional solutions. The connection between the noise damping ring and the bellhousing is of moulded design using a form conclusive and vulcanised elastomer compound and is designed to avoid rotation and radial wind up. The design provides a noticeable improvement in stiffness, resulting in a tensile strength of 56 kN, (based upon a monoblock bellhousing with a motor flange diameter of 300mm and is suitable for use with an electric motor with frame size D132). The higher stiffness results in reduced shaft misalignment and increases the service life of the drive coupling. The noise damping effect of the monobloc bellhousing is effected by the installation as well as the noise characteristics of the pump. The more annoying the pumps noise the higher the damping degree will be. The spectrum of sound level reduction generally lies between 3 dB(a) in the case of less noisy pumps (Fig. 1) and more than 10 dB(a) by pumps (Fig. 2), which produce higher levels of noise. Pump Drive Components RV Series Bellhousing (VDMA Std.) Permitted Load for Damped Bellhousings 37 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components RV Bellhousings Bellhousings with flange Ø D1 = 160 mm according to VDMA 24 561 only in rigid version. Noise reduction version with flange Ø D1 = 200 mm with screwed damping flange on request. Rigid Version RV Ø D = 160 - 350 mm according to VDMA 24 561 38 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components RV Bellhousings with noise reduction Monobloc-system, noise reduction Noise reduction version, 2-piece Ø D1 = 250 - 350 mm Ø D1 = 400 - 800 mm accordingtoVDMA 24561formfittingwithoutscrewjoint *Not included in the VDMA standard Bellhousings with flange Ø D1 = 160 mm according to VDMA 24 561 only in rigid version. Noise reduction version with flange Ø D1 = 200 mm with screwed damping flange on request. 39 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Module 3 Bellhousing How it works A range of composite bellhousings to accomodate electric motor flanges from 300mm diameter to 800mm diameter. Pump flanges Central adaptor Base module { { { 40 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Base Module Detail 41 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Central Adaptor Detail 42 #DriveLineHarmony www.jbj.co.uk/couplings.html
FPxx / + + + / K Pump Drive Components Popular Pump Flange Details Fordetailsofflangesnotshownpleasecontact jbj Techniques Limited technical office, telephone: 01737 767493 or email: info@jbj.co.uk Ordering Code 43 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Popular Machining Codes NB. Other machine codes available on request. For details please contact jbj Techniques Limited technical office, telephone: 01737 767493 or email: info@jbj.co.uk C C C 44 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Cooler Bellhousings Series KPV Technical Data • (1) Nominal rotation ofdrivenmachine1500rev/min.Incaseofdifferentrpmpleasecontactjbj Techniques TechnicalOffice. • (2) Noise levels of damped version are measured with a bellhousing and electric motor distance to the tested object of 1m. The values of noise level will vary depending on the electric motor used. • Direction of pump rotation always clockwise, looking on pump shaft. Ordering Code (2) (1) footbracket is not supplied as standard but can be supplied as an optional extra 45 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Cooler Bellhousings Series KPV footbracket is not supplied as standard but can be supplied as an optional extra 46 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Cooler Bellhousings Series KPV SpecificcoolingcapacitydependingonoilflowQ(l/min)andthetemperaturedifference Dt 2°C (Oil inlet and air inlet) Pressure drop of cooler matrix at the oil viscosity of 32 cSt 47 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components P Series Foot Brackets Material cast aluminium P160 - P300 P350 Only 48 #DriveLineHarmony www.jbj.co.uk/couplings.html
Standard material - Cast Aluminium Pump Drive Components PTFL & PTFS Series Foot Brackets PTFL PTFS 49 #DriveLineHarmony www.jbj.co.uk/couplings.html
FM-36-M3 FM-37-M3R Foot mounting bracket for small geroter torque motors. Fits Eaton M series, Danfoss, OMM and other motors with same mounting. Reversed position cast aluminium weight 0.255kg (9oz) FM-38-4F Weight 0.369 kg (13 oz) FM-39-AA2 Weight 0.454 kg (1 lb) FM-40-A2 Weight 0.765 kg (1 lb 11 oz) FM-41-A2C Weight 0.936 kg (2 lb 1 oz) FM-42-B2 Weight 1.276 kg (2 lb 13 oz) Part number ordering code eg: FM - 40 - A2 Pump flange Frame number Foot mount Foot mounting bracket for small geroter torque motors. Fits Eaton M series, Danfoss, OMM and other motors with same mounting. Standard position cast aluminium weight 0.255kg (9oz) 8.73 mm (11/32"D)ia. (2 holes). 14.29 mm (9/16") 38.1 mm (11/2") 11.11 mm (7/16") 4.76 mm (3/16") 41.28 mm (1.625") 88.9 mm (31/2") 82.55 mm (³¹⁄ ") 8.73 mm (11/32"D)ia. (2 holes). 14.29 mm (9/16") 38.1 mm (11/2") 41.28 mm (1.625") 88.9 mm (31/2") 82.55 mm (³¹⁄ ") 69.85 mm (23/4") 9.53 mm (0.375") 7.18 mm (0.281") Dia. on 44.96 mm (1.77") (3 Holes) 50.8 mm (2") 98.43 mm (37/"8) 38.1 mm (11/2") 87.31 mm (37/1"6) Bore I.D. 45.21 mm (1.78") 98.43 mm (37/"8) 38.1 mm (11/2") 87.31 mm (37/1"6) 50.8 mm (2") 130.18 mm (51/"8) 104.78 mm (41/"8) 82.55 mm (31/"4) 82.55 mm (31/"4) 130.18 mm (51/"8) 104.78 mm (41/"8) 76.2 mm (3") 139.7 mm (51/"2) 133.35 mm (51/"4) 101.6 mm (4") 82.55 mm (31/"4) 69.85 mm (23/"4) 50 #DriveLineHarmony www.jbj.co.uk/couplings.html Foot Brackets/Mountingplates Pump Drive Components
Pump Drive Components Foot Brackets/Mountingplates Mounting plate Gaskets( Material Perbunan) Standard material - Cast Aluminium 01 02 51 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Petrol Engine Adaptors Part No: PED 1/- - -/110 To suit: Honda, Briggs & Stratton, Kawasaki, Mag, Robin, Suzuki, Winsconsin, etc. Units can be machined to suit most hydraulic pump mountings. Part No: LTO 414/- - -/140 To suit: Honda, Briggs & Stratton, Kubota, etc. Units can be machined to suit most hydraulic pump mountings. Part No: PED 3/- - -/160 (STD Spigot), PED 3X/- - -/160 (Optional spigot) To suit: Honda, Briggs & Stratton, Kawasaki, Mag, Robin, Suzuki, Winsconsin, etc. Units can be machined to suit most hydraulic pump mountings. 52 #DriveLineHarmony www.jbj.co.uk/couplings.html
Pump Drive Components Petrol Engine Adaptors Part No: LTOC95/- - -/140 To suit: Kubota OC95 engine. Units can be machined to suit most hydraulic pump mountings. 53 #DriveLineHarmony www.jbj.co.uk/couplings.html Part No: LTO1B40/- - -/140 To suit: Hatz 1B40 engine. Units can be machined to suit most hydraulic pump mountings. Adaptors to suit engine camshaft drives and for vertical mounting available on request. Please contact jbj Techniques technical office, telephone: 01737 767493 or email: info@jbj.co.uk Additional reference catalogues Compatible couplings - Pump Drive Components catalogue and Torsional Couplings catalogue. Diesel engine adaptors - Pump Drives catalogue and Torsional Couplings catalogue. For pump mounting machine codes and adaptors please refer to back page of this leaflet.
Pump Drive Components Petrol Engine Adaptors Pump face machining codes (- - -) 54 #DriveLineHarmony www.jbj.co.uk/couplings.html
BACKLASH Backlash is the clearance or gap between the trailing or non-driving surfaces of the coupling jaws and flexible element, illustrated in red on the above diagram. When used in reversing or heavy cyclic applications where the coupling is required to rotate in both directions the application must be considered with the type of use, number of starts per hour considered and an appropriate service factor applied to prevent premature failure of the coupling element. Standard spider 'teeth' are curved in two directions. NON-BACKLASH The coupling element and claw profile are designed such that the element is compressed when the coupling is assembled in order to remove backlash, typical applications are for indexing or positioning drives such as lead screws or encoders where a high degree of accuracy is required. The pre-compression or preload of the element whilst providing greater accuracy also increases the dynamic torsional stiffness from 25% to 75% over the standard element at 50% of it's nominal torque rating, (depending on coupling size), thus maintaining accuracy even after extended periods of use. Nonbacklash spider 'teeth' are curved radially and parallel axially. 55 #DriveLineHarmony www.jbj.co.uk/couplings.html Pump Drive Components Backlash Explained
KEY FEATURES: » Larger Continuous Temperature Range » Higher Nominal & Max Torque » +10% Radial Misalignment » Superior Hydrolysis Resistance ~ 56 #DriveLineHarmony www.jbj.co.uk/couplings.html
Anti-Static/Flameproof Couplings Torque Limiting Couplings Torsional Couplings Screw Pumps Low Noise Helical Gear Pumps Gear Pumps/Gear Motors Pressure Intensifiers Flow Dividers Mini Power Packs Electromagnetic Clutches & Brakes BDS Clutches Coolers/Heat Exchangers Bellhousings Spider/Jaw Couplings Gear Couplings Fillers/Breathers/Filters Flame Proof Option Level Indicators Tanks/Reservoirs/Accessories www.jbj.co.uk/ .html productlist
Thermostatic Valves & Controls Torsionally Highly Flexible Couplings Torsionally Flexible Couplings Torsionally Rigid Couplings Planetary Gearboxes Multiple PTOs/Splitter Gearboxes Hydraulic Power Take-off Units Vane Pumps LSHT Motors/Hydraulic Geared Motors Pneumatic Starters & Motors Mechanical Power Take-off Units Oil Bath Clutches BD Clutches & Gearboxes Engine Adaptor Kits Dampers Bearing Supported Stub Shafts Quick Maintenance ‘QM’ Flange Flanges www.jbj.co.uk/ .html productlist
Getting the most out of your machinery often depends on close integration between all components. An organisation that manufactures and integrates all the diverse components of a drivetrain provides the experience to help you select the best component combination for your application. jbj Techniques’ in-house design team and manufacturing facility provide tailored solutions for your applications at competitive prices with quick delivery. The following examples are a simplistic view of how jbj Techniques assists customers. Hydraulic Adaptors Designed primarily to allow the close coupling of hydraulic pumps to a variety of prime movers, such as diesel / petrol engines, electric, air or hydraulic motors, they can also be used in the connection from prime mover to alternative driven parts i.e. gear boxes, generators, water or vacuum pumps etc. An additional range of engine front PTO adaptors, which provide additional connection between the engine pulley and the driven part are also available. The kit comprises of a and flexible bellhousing drive that are fully machined to suit the coupling driving and driven components. These can be to suit either shaft to shaft, flange (flywheel) to shaft or even flange to flange connections. Getting the most out of your equipment will demand close integration between all components. In specifying jbj Techniques as your preferred supplier, you will have selected a company with the experience to specify, manufacture and integrate all of the diverse components that will ensure the best component combination for your application. jbj's in house design team and manufacturing facility provide tailored solutions for your applications at competitive pricing and on-time deliveries. Pump shaft alignment is key to preventing unnecessary wear and damage to the pump shaft seal and bearing. Improper alignment may lead to premature pump failure. Also to be considered are unwanted torsional resonant frequencies in the system which can quickly cause damage to components in the drivetrain and reduce system life and performance. Improper pump installation can lead to premature failure, increased maintenance costs and reduced production levels of final product. jbj Techniques can advise on the correct installation of into Industrial / hydraulic pumps mobile / marine / machine tool / agricultural / offshore industries and can specify complete driveline systems from their extensive range of components which are available from stock or manufactured to order, albeit simple or complex, standard or bespoke. Electric Motor – Hydraulic Pump Adaptors (safe area) jbj Techniques Limited offer the most comprehensive range of in Europe. bellhousings Designed to connect electric motors with frame size IEC D56 - D400 (0.06kW – 750kW) and can be compatible with electric motor 'B5' or 'B14' flange configurations. Accompanying the metric frame units above is a complete range of mountings to suit Nema and imperial frame motors with 'C' face or 'D' flange fitments. With fully machined , torsionally flexible couplings or available, jbj ensure torsionally rigid couplings the most suitable combination is selected for the application in hand. As an example spider couplings are available in various materials including aluminium, grey cast iron, nodular iron, steel and stainless steels and can be finish machined with parallel, taper or splined bores to DIN, SAE, ANSI or ISO standards. Bellhousings can be manufactured in aluminium or cast iron material as standard, however, units can be produced in a variety of exotic materials on request. The aluminium product range is produced in either monoblock or composite formats giving great flexibility in design and allows for early delivery time, often with same or next day delivery possibilities. For applications where low noise levels are a quality products for mechanical & fluid power #DriveLineHarmony www.jbj.co.uk an excellence in engineering
ensuring a continuing high quality service in which customers can have complete confidence. “ “ requirement then a complete range of antivibration and noise reduction components add to the range. Electric motor – Hydraulic Pump Adaptors (hazardous area) Designed to meet the exacting safety standards of the offshore and chemical process industries, jbj Techniques produce certificated to adaptor kits Directive 2014/34/EU II2GD-IM2-TX -50 C< Service Temp < +105 C. Harmonised standards BS EN 1127:1, BS EN 13463:1, BS EN13463:5, BS EN 50303, BS EN 1834-1,BS EN 1834-3. Generally manufactured in Cast or Nodular iron, bellhousings can be produced in steel, stainless steel or alternative exotic materials on customer request. Couplings supplied for these applications are the jbj Techniques 'JXL' pin and bush range which provide an anti-static and flameproof drive which meet zone 1 area requirements, conforming to all of the above standards. Also available are spider and gear couplings which are certified to zone 2 standards. (Contact jbj Techniques for details). An important development of equipment for use within hazardous areas is the wet mount series of bellhousings. Commissioned to research and develop a product that would control the high temperature generated by a piston pump shaft seal when working within cycling applications. A little considered issue is the frictional heat generated at the shaft seal when the application requires the pump to cycle between different pressures causing the seal temperature to increase. This process will often take the seal temperature out and above the levels required by the relevant ATEX standards requirement. This specially designed assembly allows a pumped cooling flow to be passed over the seal face and through an auxiliary cooler, this in turn reduces the seal face temperature which can be maintained at an acceptable level. With a vast array of components to select from, jbj are well placed to provide all required components to support the required cooling system. Diesel Engine – Hydraulic Pump Adaptors A complete range of bellhousing and couplings exist for the connection of a diesel engine flywheel to a specified driven component, be it an oil hydraulic pump, water pump, generator or similar device. With the bellhousing available in various materials to suit all application areas. With a standard range to connect Diesel engines with SAE dimensions from SAE '6' to SAE '0' jbj are well placed to satisfy the majority of customer requirements. Couplings to complete the assembly are available in either torsionally flexible or torsionally rigid design ad can be supplied to suit SAE flywheel dimensions from SAE 6.5” to SAE 18”. For hydraulic pumps to be mounted to engines that do not conform to SAE dimensions, we offer a full range of assembly parts, some of which (but not all) are shown here » for diesel engines All bellhousings within this range can be finished machined to accept any, piston, vane or gear pump interfaces requested by customer. As with the electric motor range of product jbj offer complete solutions for ATEX environments, using our well proven 'JXL' coupling range which has standard design to connect to the engine flywheel. Directive 2014/34/EU II2GD-IM2-TX -50°C ≤ Service Temp ≤ +105°C. Harmonised Standards: BS EN 1127:1 BS EN 13463:1 BS EN 13463:5 BS EN 50303. Petrol Engine – Hydraulic Pump Adaptors Petrol engine adaptors have been developed for use with industrial petrol engines. Design exists to suit Honda, Briggs and Stratton, Kawasaki, Kubota, Hatz, Mag, Robin, Suzuki, Winsconsin, to name but a few, all adaptors can be finished to accept most hydraulic pumps. Adaptors to suit engine crankshaft drives and for vertical mounting are available on request. #DriveLineHarmony www.jbj.co.ukl to Large Combinations Small Individual Components
registered in England No: 1185469 jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/EC requirements set by James Harris, jbj Techniques Limited jbj Techniques Limited 28 Trowers Way Holmethorpe Industrial Estate Redhill Surrey RH1 2LW. UNITED KINGDOM 01737 767493 info@jbj.co.uk www.jbj.co.uk quality products for mechanical & fluid power
www.jbj.co.ukRkJQdWJsaXNoZXIy NzQyNjQ=