6 266.70 1 (10 / ") 2 285.75 1 (11 / ") 4 308.00 1 (12 / ") 8 8 10.32 13 ( / ") 32 196.85 3 (7 / ") 4 5 314.33 3 (12 / ") 8 333.38 1 (13 / ") 8 355.60 (14") 8 10.32 13 ( / ") 32 196.85 3 (7 / ") 4 4 361.95 1 (14 / ") 4 381.00 (15.00) 403.23 7 (15 / ") 8 12 10.32 13 ( / ") 32 196.85 3 (7 / ") 4 3 409.58 1 (16 / ") 8 428.63 7 (16 / ") 8 450.85 3 (17 / ") 4 12 10.32 13 ( / ") 32 247.65 3 (9 / ") 4 2 447.68 5 (17 / ") 8 466.73 3 (18 / ") 8 488.95 1 (19 / ") 4 12 10.32 13 ( / ") 32 247.65 3 (9 / ") 4 1 511.18 1 (20 / ") 8 530.23 7 (20 / ") 8 552.45 3 (21 / ") 4 12 11.91 15 ( / ") 32 247.65 3 (9 / ") 4 ¹/ 584.20 (23") 619.13 3 (24 / ") 8 647.70 1 (25 / ") 2 12 13.49 17 ( / ") 32 247.65 3 (9 / ") 4 0 647.70 1 (25 / ") 2 679.45 3 (26 / ") 4 711.20 (28) 16 13.49 17 ( / ") 32 323.85 3 (12 / ") 4 V W Y L HandLever Travel (Degrees) Z 54.13 (2.131) 11 42.86 (1 / ") 16 3 30.2 (1 / ") 16 13° 76.20 (3.00) 47.75 (1.88) 7 36.51 (1 / ") 16 7 62.0 (2 / ") 16 17° 3 390.65 (15 / ") 8 50.85 (2.002) 3 44.45 (1 / ") 4 1 54.0 (2 / ") 8 15° (15.00) 76.20 (3.00) 81.03 (3.19) 17 57.55 (2 / ") 64 15.5° 3 390.65 (15 / ") 8 17 57.55 (2 / ") 64 95.25 (3.75) 103.12 (4.06) 5 58.74 (2 / ") 16 9 39.6 (1 / ") 16 15.5° 114.3 (4.50) 168.15 (6.62) 17 57.55 (2 / ") 64 18° 138.18 (5.44) 18° 3 593.73 (23 / ") 8 168.40 (6.63) 13 71.43 (2 / ") 16 25.4 (1") 18° 114.3 (4.50) 194.56 (7.66) 13 71.43 (2 / ") 16 25.4 (1") 17.75° 3 593.73 (23 / ") 8 114.3 (4.50) 196.85 (7.75) 13 71.43 (2 / ") 16 25.4 (1") 18° 3 593.73 (23 / ") 8 114.3 (4.50) 245.62 (9.67) 13 71.43 (2 / ") 16 25.4 (1") 17.75° 3 593.73 (23 / ") 8 139.7 (5.50) 246.13 (9.69) 7 81.76 (3 / ") 32 5 15.87 ( / ") 8 20° 762.00 (30) 266.70 (10.50) 139.7 (5.50) 342.90 (13.50) 7 81.76 (3 / ") 32 5 15.87 ( / ") 8 20° 1066.80 (42) 139.7 (5.50) 298.45 (11.75) 13 96.84 (3 / ") 16 0.00 20° 1066.80 (42) 139.7 (5.50) 342.90 (13.50) 13 96.84 (3 / ") 16 0.00 20° 1066.80 (42) Part Number From SAE Engine Housing To SAE Clutch Housing B6320 2 4 6880 1 2 A7210 1 8407 0 1 6964 00 0 Standard Mechanical Power Take-off Units Dimensions 10 #DriveLineHarmony 00 787.40 (31") 850.90 1 (33 / ") 2 882.65 3 (34 / ") 4 16 13.49 17 ( / ") 32 425.45 3 (16 / ") 4 Dimensional Data, dimensions in mm (inches) Housing Flanges SAE Housing No. A R B.C. S Dia. T Holes No. Dia. P ¹/ www.jbj.co.uk/mechanical-power-conversion.html USE A CERTIFIED PRINT FOR INSTALLATION NOTE: PTO models with OP designation have oil-lubricated main bearings. All other models have grease-lubricated main bearings. IMPORTANT NOTICE 1. A support plate for one-plate SAE 14 and smaller PTOs (except SP-311P) is not required. 2. A support plate for three-plate SAE 11.5 and two- and three-plate SAE 14 PTOs is required in side-load applications and is recommended for in-line applications. 3. A support plate for SAE 18 and larger PTOs is required for both side-load and in-line applications. Dimensions of these industrial PTOs with drive ring and over-centre clutch conform to the recommendations of SAE J621 (latest revision) unless noted. Adapter Rings (spaceless)
RkJQdWJsaXNoZXIy NzQyNjQ=