uk distributor for quality products for mechanical & fluid power jbj Techniques Limited, www.jbj.co.uk FP12 FERRA SERIES HEAVY DUTY GEAR PUMP
Concentric AB-FERRA F12 SERIES-2011-06 2 DESIGNED FOR HEAVY DUTY The FERRA F12 pump is a rugged two-piece pump available with displacements from 16 to 41 cc/rev and pressures up to 276 bar (4000 psi up to 30 cc/ rev). FERRA pumps feature cast iron construction, resulting in a compact unit that is extremely robust across a broad temperature range, while also o ering increased power density and good installation characteristics compared with conventional designs. Both the housing and the front cover are of cast iron, which has made it possible to eliminate the rear cover, integrate the gearing into the housing and make the whole unit more compact. Ferra Pump Quick Data Target Markets • Construction machinery • Agricultural • Material Handling Equipment Displacement Range • Displacements from 16 to 41cc/rev (0.976 to 2.502 in/rev) Special Design Features • Compact design with high power density and available at optimum cost • Cast iron housing • State-of-the-art gear geometry for reduced pressure pulsation and low noise operation • Wide operating range • SAE “A” and SAE “B” interfaces Design Options • Multiple section pumps available • Interframe capability with W900 pump possible • Double shaft seal • Integrated valve options PERFORMANCE SPECIFICATIONS for FP12 FERRA Pumps Size Code Theoretical Displacement Per Revolution Continuous Rated Pressure P1 Max Rated Speed @ Rated Pressure Min Rated Speed @ Rated Pressure Typical Delivery @ Rated Speed And Pressure Typical Input Power @ Rated Speed And Pressure # cc / c.i.r. bar / psi rpm rpm lpm / gpm kW / HP 160 16 / 0.976 276 / 4000 3000 500 44.6 / 11.8 22.8 / 30.6 190 19 / 1.159 276 / 4000 3000 500 53.0 / 14.0 27.0 / 36.2 230 23 / 1.404 276 / 4000 3000 500 64.2 / 17.0 32.7 / 43.9 270 27 / 1.648 276 / 4000 3000 500 75.3 / 19.9 38.4 / 51.5 300 30 / 1.831 276 / 4000 3000 500 83.7 / 22.1 42.7 / 57.3 330 33 / 2.014 250 / 3600 2800 500 85.9 / 22.7 39.7 / 53.2 350 35 / 2.136 225 / 3250 2600 500 84.6 / 22.3 35.2 / 47.2 410 41 / 2.502 180 / 2600 2300 500 87.7 / 23.2 29.2 / 39.2 The bearings are located in the housing and the ange, while two pressure plates ensure high volumetric e ciency at low speeds. The FERRA pump’s gear pro le is of an advanced design optimized for reduced pulsation and high power density in relation to the unit’s relatively small package size. Extensive testing has demonstrated that the FERRA pump matches or exceeds competitors’ products in a smaller package and o ers signi cantly better performance at low speeds. Both bench tests and in-vehicle tests have shown that the design is highly suitable for high- ow implement and steering circuits and fan drive applications. quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 3 FP12A1 Single Pump Size Code Displacement A B with SAE “B” Flange ‘05’ with SAE “A” Flange ‘03’ # cc/rev c.i.r. mm [in] mm [in] kg [lb] kg [lb] 160 16 0.976 112.3 [4.4] 70.2 [2.8] 6.7 [14.8] 6.1 [13.4] 190 19 1.159 116.1 [4.6] 72.1 [2.8] 6.9 [15.2] 6.3 [13.9] 230 23 1.404 121.2 [4.8] 74.7 [2.9] 7.1 [15.7] 6.5 [14.3] 270 27 1.648 126.3 [5.0] 77.2 [3.0] 7.3 [16.1] 6.7 [14.8] 300 30 1.831 130.2 [5.1] 79.2 [3.1] 7.4 [16.3] 6.8 [15.0] 330 33 2.014 134.0 [5.3] 81.1 [3.2] 7.6 [16.8] 7.0 [15.4] 350 35 2.136 136.6 [5.4] 82.4 [3.2] 7.7 [17.0] 7.1 [15.7] 410 41 2.502 144.2 [5.7] 86.2 [3.4] 8.0 [17.6] 7.4 [16.3] SINGLE PUMP DIMENSIONS FP12A1 INLET OUTLET CW ROTATION 177 [6.97] 133 [5.24] 146 [5.75] 2X 14.7 [.58] 14.3 [.56] THRU 87 [3.43] 107 [4.21] 70.8 [2.79] 21.0 [.83] 40.7 [1.60] 17.5 [.69] 2X 9.4 [.37] B 20.5 [.81] A 41.7 [1.64] 9.6 [.38] 14.5 [.57] 14.0 [.55] 101.60 [4.00] 101.55 [3.99] 21.80 [.86] 21.68 [.85] All dimensions are mm [in]. quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 4 TANDEM PUMP DIMENSIONS FP12A2 FP12A2 Tandem Pump Size Code Displacement SECTION 2 SECTION 1 A B with SAE “B” Flange ‘05’ with SAE “A” Flange ‘03’ C D # cc/rev c.i.r. mm [in] mm [in] kg [lb] kg [lb] mm [in] mm [in] kg [lb] 160 16 0.976 120.6 [4.7] 79.1 [3.1] 7.5 [16.5] 6.9 [15.2] 65.4 [2.6] 32.7 [1.3] 4.1 [9.0] 190 19 1.159 124.4 [4.9] 81.0 [3.2] 7.7 [17.0] 7.1 [15.7] 69.2 [2.7] 34.6 [1.4] 4.3 [9.5] 230 23 1.404 129.5 [5.1] 83.5 [3.3] 7.9 [17.4] 7.3 [16.1] 74.3 [2.9] 37.2 [1.5] 4.5 [9.9] 270 27 1.648 134.6 [5.3] 86.1 [3.4] 8.1 [17.9] 7.5 16.5] 79.4 [3.1] 39.7 [1.6] 4.7 [10.4] 300 30 1.831 138.5 [5.5] 88.0 [3.5] 8.2 [18.1] 7.6 [16.8] 83.3 [3.3] 41.7 [1.6] 4.8 [10.6] 330 33 2.014 142.3 [5.6] 89.9 [3.5] 8.4 [18.5] 7.8 [17.2] 87.1 [3.4] 43.6 [1.7] 5.0 [11.0] 350 35 2.136 144.9 [5.7] 91.2 [3.6] 8.5 [18.7] 7.9 [17.4] 89.7 [3.5] 44.9 [1.8] 5.1 [11.2] 410 41 2.502 152.5 [6.0] 95.0 [3.7] 8.8 [19.4] 8.2 [18.1] 97.3 [3.8] 48.7 [1.9] 5.4 [11.9] 120 [4.72] CW ROTATION OUTLET INLET 146 [5.75] 2X 14.17 [.56] 14.55 [.57] 174 [6.85] 17.5 [.69] A B 101.55 [3.99] D 101.60 [4.00] C 87 [3.43] 107 [4.21] 70.8 [2.79] All dimensions are mm [in]. quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 5 TRIPLE PUMP DIMENSIONS FP12A3 FP12A3 Triple Pump Size Code Displacement SECTION 2 SECTION 2 SECTION 1 A B with SAE “B” Flange ‘05’ with SAE “A” Flange ‘03’ C D E F # cc/rev c.i.r. mm [in] mm [in] kg [lb] kg [lb] mm [in] mm [in] kg [lb] mm [in] mm [in] kg [lb] 160 16 0.976 120.6 [4.7] 79.1 [3.1] 7.5 [16.5] 6.9 [15.2] 83.1 [3.3] 41.6 [1.6] 4.9 [10.8] 65.4 [2.6] 32.7 [1.3] 4.1 [9.0] 190 19 1.159 124.4 [4.9] 81.0 [3.2] 7.7 [17.0] 7.1 [15.7] 86.9 [3.4] 43.5 [1.7] 5.1 [11.0] 69.2 [2.7] 34.6 [1.4] 4.3 [9.5] 230 23 1.404 129.5 [5.1] 83.5 [3.3] 7.9 [17.4] 7.3 [16.1] 92.0 [3.6] 46.0 [1.8] 5.3 [11.7] 74.3 [2.9] 37.2 [1.5] 4.5 [9.9] 270 27 1.648 134.6 [5.3] 86.1 [3.4] 8.1 [17.9] 7.5 16.5] 97.1 [3.8] 48.6 [1.9] 5.5 [12.1] 79.4 [3.1] 39.7 [1.6] 4.7 [10.4] 300 30 1.831 138.5 [5.5] 88.0 [3.5] 8.2 [18.1] 7.6 [16.8] 101.0 [4.0] 50.5 [2.0] 5.6 [12.3] 83.3 [3.3] 41.7 [1.6] 4.8 [10.6] 330 33 2.014 142.3 [5.6] 89.9 [3.5] 8.4 [18.5] 7.8 [17.2] 104.8 [4.1] 52.4 [2.1] 5.8 [12.8] 87.1 [3.4] 43.6 [1.7] 5.0 [11.0] 350 35 2.136 144.9 [5.7] 91.2 [3.6] 8.5 [18.7] 7.9 [17.4] 107.4 [4.2] 53.7 [2.1] 5.9 [13.0] 89.7 [3.5] 44.9 [1.8] 5.1 [11.2] 410 41 2.502 152.5 [6.0] 95.0 [3.7] 8.8 [19.4] 8.2 [18.1] 115.0 [4.5] 57.5 [2.3] 6.2 [13.7] 97.3 [3.8] 48.7 [1.9] 5.4 [11.9] 120 [4.72] CW ROTATION OUTLET INLET 146 [5.75] 2X 14.17 [.56] 14.55 [.57] 174 [6.85] 17.5 [.69] A B 101.55 [3.99] F 101.60 [4.00] E C D 87 [3.43] 107 [4.21] 70.8 [2.79] All dimensions are mm [in]. quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 6 MULTIPLE PUMP DIMENSIONS (Interframe) FT12A1/WP09A1 FT12A1 SECTION 1 Size Code Displacement A B with SAE “B” Flange ‘05’ with SAE “A” Flange ‘03’ # cc/rev c.i.r. mm [in] mm [in] kg [lb] kg [lb] 160 16 0.976 99.0 [3.9] 68.3 [2.7] 6.5 [14.3] 5.9 [13.0] 190 19 1.159 102.8 [4.0] 70.2 [2.8] 6.6 [14.6] 6.0 [13.2] 230 23 1.404 107.9 [4.2] 72.7 [2.9] 6.8 [15.0] 6.2 [13.7] 270 27 1.648 113.0 [4.4] 75.3 [3.0] 7.0 [15.4] 6.4 [14.1] 300 30 1.831 116.9 [4.6] 77.2 [3.0] 7.2 [15.9] 6.6 [14.6] 330 33 2.014 120.7 [4.8] 79.1 [3.1] 7.3 [16.1] 6.7 [14.8] 350 35 2.136 123.3 [4.9] 80.4 [3.2] 7.4 [16.3] 6.8 [15.0] 410 41 2.502 130.9 [5.2] 84.2 [3.3] 7.7 [17.0] 7.1 [15.7] WP09A1 SECTION 2 Size Code Displacement C D # cc/rev c.i.r. mm [in] mm [in] kg [lb] 005 5 0.305 74.6 [2.9] 24.8 [1.0] 2.0 [4.4] 008 8 0.488 79.1 [3.1] 27.1 [1.1] 2.1 [4.6] 011 11 0.674 83.5 [3.3] 29.3 [1.2] 2.2 [4.9] 016 16 0.976 90.9 [3.6] 33.0 [1.3] 2.4 [5.3] 019 19 1.159 95.4 [3.8] 35.2 [1.4] 2.6 [5.7] 023 23 1.404 101.3 [4.0] 38.2 [1.5] 2.7 [6.0] 027 27 1.648 107.2 [4.2] 41.1 [1.6] 2.9 [6.4] 030 30 1.831 111.7 [4.4] 43.4 [1.7] 3.0 [6.6] 133 [5.24] CW ROTATION OUTLET INLET 146 [5.75] 2X 14.3 [.56] 14.7 [.58] 177 [6.97] A B 101.55 [3.99] D 101.60 [4.00] C 21.68 [.85] 21.80 [.86] 20.5 [.81] 21.0 [.83] 40.7 [1.60] 41.7 [1.64] 90.8 [3.57] 107 [4.21] 70.8 [2.79] All dimensions are mm [in]. quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 7 MOUNTING FLANGES SAE “A” 2-BOLT, Flange Code “03” SAE “B” 2-BOLT, Flange Code “05” SHAFT CODE “KA” SHAFT CODE “GA” DRIVE SHAFTS EXTERNAL INVOLUTE SPLINE SAE-STD. Flat Root - Side Fit No. of Teeth: 11 Diametral Pitch - 16/32 PRESSURE ANGLE - 30° Mt max. 170 Nm EXTERNAL INVOLUTE SPLINE SAE-STD. Flat Root - Side Fit No. of Teeth: 13 Diametral Pitch - 16/32 PRESSURE ANGLE - 30° Mt max. 270 Nm 6.35 [.25] 6.10 [.24] 82.50 [3.24] 82.55 [3.25] 2X 11.3 [.45] 11.7 [.46] 106.4 [4.19] 97 [3.82] 2X 11.0 [.43] 11.4 [.45] 130 [5.12] 146 [5.75] 121 [4.76] 2X 14.17 [.56] 14.55 [.57] 174 [6.85] 9.6 [.38] 9.4 [.37] 101.55 [3.99] 101.60 [4.00] 2X 14.0 [.55] 14.5 [.57] 21.0 [.83] 20.5 [.81] 21.68 [.85] 21.80 [.86] 40.7 [1.60] 41.7 [1.64] 33.3 [1.31] 33.5 [1.32] 24.1 [.95] 23.4 [.92] 18.49 [.72] 18.62 [.73] 37.5 [1.48] 38.5 [1.52] 31.0 [1.22] 31.4 [1.24] All dimensions are mm [in]. quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 8 PORTS Inlet Outlet Inlet Outlet CODE 150 CODE 151 COD M6 x 13 90° 20 40 M6 x 13 90° 15 35 COD M8 x 13 90° 26 55 M8 x 13 18 55 34.1 [1.34] 7/8-14 UNF-2B CODE 102 Inlet Outlet CODE 104 Inlet Outlet ] 48.5 [1.91] 1-5/16-12 UN-2B CODE 103 Inlet Outlet 41.3 [1.63] 1-1/16-12 UN-2B Inlet Outlet Inlet Outlet Inlet Outlet CODE 122 CODE [141] 146* CODE [142] 147* G1 x 18 G3/4 x 16 M10 x 16 [3/8-16] 26.2 [1.03] [SAE 1”] 25 52.4 [2.06] M10 x 16 [3/8-16] 22.2 [0.87] [SAE 3/4”] 19 47.6 [1.87] M10 x 16 [7/16-14] 30.2 [1.89] [SAE 1-1/4”] 32 58.6 [2.31] M10 x 16 [3/8-16] 26.2 [1.03] [SAE 1”] 25 52.4 [2.06] * Check availability for small displacements. 38.1 [1.50] 6.4 [.25] 39.8 [1.57] 43.5 [1.71] TUBE FITTING 57.7 [2.27] 1-5/8-12 UN-2B 48.5 [1.91] 1-5/16-12 UN-2B 41.3 [1.63] 1-1/16-12 UN-2B All dimensions are mm [in]. Inlet Outlet 41.3 [1.63] 1-1/16-12 UN-2B quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 9 Model Code for FP12 Ferra Series Pumps FP 12 A 4 B 270 160 160 160 R 05 KA 151 151 151 151 N E 1 2 3 4 5 6.1 6.2 6.3 6.4 7 8 9 10.1 10.2 10.3 10.4 11 12 TYPE SERI ES DESI GN # OF SEC TION S SEAL MAT ERIA L DISP LACE MEN T 1 DISP LACE MEN T 2 DISP LACE MEN T 3 DISP LACE MEN T 4 ROTA TION MOU NTIN G FL ANG E DRIV E SH AFT POR TS 1 POR TS 2 POR TS 3 POR TS 4 VALV E OP TION S SPEC IALS 1. Type Order Code Description FP12 Ferra Pump 2. Series Order Code Description 12 Series 12 = 1200 3. Design Order Code Description A Ferra Design 4. No. of Sections Order Code Description 1 Single 2 Double 3 Triple 4 Quadruple 5. Seal Material Order Code Description B Buna V Viton C Combined 6. Displacements Order Code Description 016 16 cm3 / 0.976 in3 019 19 cm3 / 1.159 in3 023 23 cm3 / 1.404 in3 027 27 cm3 / 1.648 in3 030 30 cm3 / 1.831 in3 033 33 cm3 / 2.014 in3 035 35 cm3 / 2.136 in3 041 41 cm3 / 2.502 in3 7. Rotation Order Code Description R CW - Clockwise L CCW - Counter Clockwise 8. Front Cover Order Code Description 03 SAE “A” 2-Bolt Mount - Pilot Ø 82.5 05 SAE “B” 2-Bolt Mount - Pilot Ø 101.55 9. Drive Shaft Order Code Description KA SAE “B” 13-Tooth Spline, Flat Root-Side Fit GA SAE “A” 11-Tooth Spline, Flat Root-Side Fit 10. Ports Order Code Description Low (Inlet) High (Outlet) Type 102 1-1/16-12 7/8-14 SAE 103 1-5/16-12 1-1/16-12 SAE 104 1-5/8-12 1-5/16-12 SAE 122 G1x18 mm G3/4x16 mm BSPP [141] 146* [1”] 25 mm [3/4”] 19 mm [SAE] Metric Split Flange [142] 147* [1-1/4”] 32 mm [1”] 25 mm [SAE] Metric Split Flange 150 20 mm 15 mm Euro 4-Bolt Split Flange 151 26 mm 18 mm Euro 4-Bolt Split Flange 861 1-1/2” 1-1/16” Special Beaded Hose Fitting/SAE * Check availability for small displacements. 11. Valve Options Order Code Description N None 12. Specials Order Code Description Exxxx “E” + Special No. - None Example (Single Pump): FP-12-A-1-B-270-R-05-KA-151-N-E Example (Double Pump): FP-12-A-2-B-270-160-R-05-KA-151-151-N-E Example (Triple Pump): FP-12-A-3-B-270-160-160-R-05-KA-151-151-151-N-E Example (Quadruple Pump): FP-12-A-4-B-270-160-160-160-R-05-KA-151-151-151-151-N-E quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Concentric AB-FERRA F12 SERIES-2011-06 10 Model Code for FT12A1/WP09A1 Ferra Series Interframe Pumps FT 12 A 1 B 270 R 05 KA 151 N E 1 2 3 4 5 6.1 7 8 9 10.1 11 12 1. Type Order Code Description FT Ferra Thru-Drive Pump 2. Series Order Code Description 12 Series 12 = 1200 3. Design Order Code Description A Ferra Design 4. No. of Sections Order Code Description 1 Single 5. Seal Material Order Code Description B Buna V Viton C Combined 6. Displacement (FT12 only - seeW900 Catalog for WP9) Order Code Description 016 16 cm3 / 0.976 in3 019 19 cm3 / 1.159 in3 023 23 cm3 / 1.404 in3 027 27 cm3 / 1.648 in3 030 30 cm3 / 1.831 in3 033 33 cm3 / 2.014 in3 035 35 cm3 / 2.136 in3 041 41 cm3 / 2.502 in3 7. Rotation Order Code Description R CW - Clockwise L CCW - Counter Clockwise 8. Front Cover Order Code Description 03 SAE “A” 2-Bolt Mount - Pilot Ø 82.5 05 SAE “B” 2-Bolt Mount - Pilot Ø 101.55 9. Drive Shaft Order Code Description KA SAE “B” 13-Tooth Spline, Flat Root-Side Fit GA SAE “A” 11-Tooth Spline, Flat Root-Side Fit 10. Ports (FT12 Ports - see W900 Catalog for WP9 Ports) Order Code Description Low High 102 1-1/16-12 7/8-14 SAE 103 1-5/16-12 1-1/16-12 SAE 104 1-5/8-12 1-5/16-12 SAE 122 G1x18 mm G3/4x16 mm BSPP [141] 146* [1”] 25 mm [3/4”] 19 mm [SAE] Metric Split Flange [142] 147* [1-1/4”] 32 mm [1”] 25 mm [SAE] Metric Split Flange 150 20 mm 15 mm Euro 4-Bolt Split Flange 151 26 mm 18 mm Euro 4-Bolt Split Flange 861 1-1/2” 1-1/16” Special Beaded Hose Fitting/SAE * Check availability for small displacements. 11. Valve Options Order Code Description N None 12. Specials Order Code Description Exxxx “E” + Special No. - None WP 09 A 1 B 016 R 99 ZZ 151 N E 1 2 3 4 5 6.2 7 8 9 10.2 11 12 Example (F12 Thru-Drive Pump / W900 Pump Interframe Combination): FT-12-A-1-B-270-R-05-KA-151-N-E / WP-09-A-1-B-016-R-99-ZZ-N-E Below shows options for the FT12 Thru-Drive Pump section only. SeeW900 pump catalog for W900 pump options referenced above. TYPE SERI ES DESI GN # OF SEC TION S SEAL MAT ERIA L DISP LACE MEN T ROTA TION MOU NTIN G FL ANG E DRIV E SH AFT POR TING S VALV E OP TION S SPEC IALS TYPE SERI ES DESI GN # OF SEC TION S SEAL MAT ERIA L DISP LACE MEN T ROTA TION MOU NTIN G FL ANG E DRIV E SH AFT POR TING S VALV E OP TION S SPEC IALS quality products for mechanical & fluid power ~ jbj Techniques Limited, www.jbj.co.uk UK distributor for Concentric Hydraulics
Cast Iron Pumps Heavy Duty GC Series Pumps Displacements 1.06 to 11.65 cc GC Series High/Low Pumps High Pressure Displacements 1.06 to 4.22 cc Low Pressure Displacements 4.22 to 12.71 cc Maximum Pressure 276 bar Maximum Speed 4,000 rpm W-Series Pumps W100 Displacements 0.50 to 2.00 cc W300 Displacements 0.80 to 5.70 cc W600 Displacements 4 to 12 cc W900 Displacements 5 to 31 cc W1200 Displacements 25 to 33 cc W1500 Displacements 19 to 50 cc Maximum Pressure 276 bar Maximum Speed 500 to 4,000 rpm D Series Pumps Displacements 03.80 to 22.85 cc D Series High/Low Pumps High Pressure Displacements 7.62 cc Low Pressure Displacements 15.24 to 22.86 cc Maximum Pressure 207–276 bar Maximum Speed 3,600–4,000 rpm WK900 CALMA Pumps Displacements 5 to 27 cc Maximum Pressure 230 bar Maximum Speed 4,000 rpm F12 & F15 Ferra Series Pumps F12 Displacements 16 – 41 cc F15 Displacements 19 to 50 cc Maximum Pressure 276 bar Maximum Speed 3,600 rpm Cast Iron Displacements 1.06 to 161 cc Speed Up to 10,000 rpm Aluminum Displacements 4 to 50 cc Speed Up to 4,000 rpm Flow Dividers Fluid Motors GC & D Series GC Displacements 1.58 to 8.47 cc D Displacements 3.8 to 13.32 cc Maximum Pressure 310 bar Maximum Input Flow Per Section 14 gpm (53 lpm) Aluminum Pumps Medium/Light Duty F20/F30 Pumps & F20-LS/F30-LS Load Sense Ferra Series Pumps Displacements 23 to 161 cc Maximum Pressure 276 bar Maximum Speed 3,600 rpm PUMPS & MOTORS
Getting the most out of your machinery often depends on close integration between all components. An organisation that manufactures and integrates all the diverse components of a drivetrain provides the experience to help you select the best component combination for your application. jbj Techniques’ in-house design team and manufacturing facility provide tailored solutions for your applications at competitive prices with quick delivery. The following examples are a simplistic view of how jbj Techniques assists customers. Hydraulic Adaptors Designed primarily to allow the close coupling of hydraulic pumps to a variety of prime movers, such as diesel / petrol engines, electric, air or hydraulic motors, they can also be used in the connection from prime mover to alternative driven parts i.e. gear boxes, generators, water or vacuum pumps etc. An additional range of engine front PTO adaptors, which provide additional connection between the engine pulley and the driven part are also available. The kit comprises of a and flexible bellhousing drive that are fully machined to suit the coupling driving and driven components. These can be to suit either shaft to shaft, flange (flywheel) to shaft or even flange to flange connections. Getting the most out of your equipment will demand close integration between all components. In specifying jbj Techniques as your preferred supplier, you will have selected a company with the experience to specify, manufacture and integrate all of the diverse components that will ensure the best component combination for your application. jbj's in house design team and manufacturing facility provide tailored solutions for your applications at competitive pricing and on-time deliveries. Pump shaft alignment is key to preventing unnecessary wear and damage to the pump shaft seal and bearing. Improper alignment may lead to premature pump failure. Also to be considered are unwanted torsional resonant frequencies in the system which can quickly cause damage to components in the drivetrain and reduce system life and performance. Improper pump installation can lead to premature failure, increased maintenance costs and reduced production levels of final product. jbj Techniques can advise on the correct installation of into Industrial / hydraulic pumps mobile / marine / machine tool / agricultural / offshore industries and can specify complete driveline systems from their extensive range of components which are available from stock or manufactured to order, albeit simple or complex, standard or bespoke. Electric Motor – Hydraulic Pump Adaptors (safe area) jbj Techniques Limited offer the most comprehensive range of in Europe. bellhousings Designed to connect electric motors with frame size IEC D56 - D400 (0.06kW – 750kW) and can be compatible with electric motor 'B5' or 'B14' flange configurations. Accompanying the metric frame units above is a complete range of mountings to suit Nema and imperial frame motors with 'C' face or 'D' flange fitments. With fully machined , torsionally flexible couplings or available, jbj ensure torsionally rigid couplings the most suitable combination is selected for the application in hand. As an example spider couplings are available in various materials including aluminium, grey cast iron, nodular iron, steel and stainless steels and can be finish machined with parallel, taper or splined bores to DIN, SAE, ANSI or ISO standards. Bellhousings can be manufactured in aluminium or cast iron material as standard, however, units can be produced in a variety of exotic materials on request. The aluminium product range is produced in either monoblock or composite formats giving great flexibility in design and allows for early delivery time, often with same or next day delivery possibilities. For applications where low noise levels are a quality products for mechanical & fluid power #DriveLineHarmony www.jbj.co.uk an excellence in engineering
ensuring a continuing high quality service in which customers can have complete confidence. “ “ requirement then a complete range of antivibration and noise reduction components add to the range. Electric motor – Hydraulic Pump Adaptors (hazardous area) Designed to meet the exacting safety standards of the offshore and chemical process industries, jbj Techniques produce certificated to adaptor kits Directive 2014/34/EU II2GD-IM2-TX -50 C< Service Temp < +105 C. Harmonised standards BS EN 1127:1, BS EN 13463:1, BS EN13463:5, BS EN 50303, BS EN 1834-1,BS EN 1834-3. Generally manufactured in Cast or Nodular iron, bellhousings can be produced in steel, stainless steel or alternative exotic materials on customer request. Couplings supplied for these applications are the jbj Techniques 'JXL' pin and bush range which provide an anti-static and flameproof drive which meet zone 1 area requirements, conforming to all of the above standards. Also available are spider and gear couplings which are certified to zone 2 standards. (Contact jbj Techniques for details). An important development of equipment for use within hazardous areas is the wet mount series of bellhousings. Commissioned to research and develop a product that would control the high temperature generated by a piston pump shaft seal when working within cycling applications. A little considered issue is the frictional heat generated at the shaft seal when the application requires the pump to cycle between different pressures causing the seal temperature to increase. This process will often take the seal temperature out and above the levels required by the relevant ATEX standards requirement. This specially designed assembly allows a pumped cooling flow to be passed over the seal face and through an auxiliary cooler, this in turn reduces the seal face temperature which can be maintained at an acceptable level. With a vast array of components to select from, jbj are well placed to provide all required components to support the required cooling system. Diesel Engine – Hydraulic Pump Adaptors A complete range of bellhousing and couplings exist for the connection of a diesel engine flywheel to a specified driven component, be it an oil hydraulic pump, water pump, generator or similar device. With the bellhousing available in various materials to suit all application areas. With a standard range to connect Diesel engines with SAE dimensions from SAE '6' to SAE '0' jbj are well placed to satisfy the majority of customer requirements. Couplings to complete the assembly are available in either torsionally flexible or torsionally rigid design ad can be supplied to suit SAE flywheel dimensions from SAE 6.5” to SAE 18”. For hydraulic pumps to be mounted to engines that do not conform to SAE dimensions, we offer a full range of assembly parts, some of which (but not all) are shown here » for diesel engines All bellhousings within this range can be finished machined to accept any, piston, vane or gear pump interfaces requested by customer. As with the electric motor range of product jbj offer complete solutions for ATEX environments, using our well proven 'JXL' coupling range which has standard design to connect to the engine flywheel. Directive 2014/34/EU II2GD-IM2-TX -50°C ≤ Service Temp ≤ +105°C. Harmonised Standards: BS EN 1127:1 BS EN 13463:1 BS EN 13463:5 BS EN 50303. Petrol Engine – Hydraulic Pump Adaptors Petrol engine adaptors have been developed for use with industrial petrol engines. Design exists to suit Honda, Briggs and Stratton, Kawasaki, Kubota, Hatz, Mag, Robin, Suzuki, Winsconsin, to name but a few, all adaptors can be finished to accept most hydraulic pumps. Adaptors to suit engine crankshaft drives and for vertical mounting are available on request. #DriveLineHarmony www.jbj.co.ukl to Large Combinations Small Individual Components
to Large Combinations from Small Individual Components ensuring a continuing high quality service in which customers can have complete confidence. “ “ # Driveline jbj Techniques is a specialist supplier of high-quality products for the mechanical power transmission and fluid power sectors. The company offers a high level of in-house expertise plus a huge selection of products to meet a very broad range of customer applications. From specification, through technical advice and manufacture to after-sales support, jbj Techniques provides a comprehensive and valued service to the power transmission and hydraulics industries. The company fields a UK-wide team of technical sales engineers to ensure that the business is close to its customers, and it enjoys excellent associations with European manufacturers, acting as sole UK distributor in many cases. jbj’s team is recognised for its expertise in the selection and configuration of hydraulic and mechanical transmission systems. Able to draw on an that extensive product range provides the building blocks for bespoke systems both large and small, the in-house design team offers a complete service, ranging from an assessment of customer requirements to full technical backup, including product specification, CAD based system design, system build and certification. Moreover customers can take advantage of jbj’s own machine-shop facilities and skilled engineers guarantee to quality and control costs. jbj Techniques provides one of the widest ranges of couplings available within the UK; mechanical power transmission couplings for a vast range of applications. Ranging from miniature couplings, all steel gear couplings, flexible spider couplings, shaft couplings, torque limiting couplings, disc and grid type couplings, ATEX compliant and shaft locking devices. Magnetic couplings for power transmission between hermetically sealed areas. However as extensive as the selection is, couplings make up a fraction of jbj’s portfolio. As power transmission specialists the company stock and provide gearboxes, clutches, pumps, hydraulic motors, flow meters, fluid power accessories including: cooling & heat exchange products, reservoirs, pipe flanges, seals and level indicators, as well as a variety of bellhousings and engine adaptors, to name just a few of the product categories. jbj Techniques Limited is proud of it’s relationship and reputation with customers and suppliers. The core client base is stable and loyal, which is testament to the quality of service provided by the company. A similar relationship exists with suppliers, ensuring a continuing high quality service in which customers can have complete confidence. Dampers Engine Adaptor Kits Hydraulic Adaptors Torque Limiting Couplings Tyre Couplings Anti-static/Flameproof Couplings Torsionally Rigid Couplings Torsionally Flexible Couplings Bellhousings Permanent Magnetic Couplings Torsional Couplings
ne Harmony comprehensive range of components www.jbj.co.uk an excellence in engineering 01737 767493 info@jbj.co.uk www.jbj.co.uk - registered in England No: 1185469 - jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/E requirements Screw Pumps Pneumatic Motors & Starters Gear Pumps/Motors Axial & Radial Piston Motors Vane Pumps LSHT Motors/Geared Motors Splitter Gearboxes Planetary Gearboxes BDS Clutches BD Clutches & Gearboxes Oil Bath Clutches Flow Dividers Tanks/Accessories Fluid Level Indicators Flanges Mini Power Packs Coolers Pressure Intensifiers You Tube
uk distributor for quality products for mechanical & fluid power jbj Techniques Limited www.jbj.co.uk 28 Trowers Way, Holmethorpe Industrial Estate Redhill, Surrey RH1 2LW UNITED KINGDOM tel: 01737 767493 fax: 01737 772041 email: info@jbj.co.uk Concentric will not accept responsibility for any catalogue errors and reserves the right to modify its products without prior notice. This also applies to products already ordered, provided that such modifications can be made without affecting technical specifications. All trademarks in this material are properties of their respective owners. Concentric is an innovator in flow control and fluid power, supplying proprietary systems and components for trucks, buses and industrial vehicles, worldwide. With 1,156 employees and yearly sales exceeding 1,977 million Swedish Kronor, Concentric AB is listed on the Stockholm Stock Exchange (www.concentricAB.com).
www.jbj.co.ukRkJQdWJsaXNoZXIy NzQyNjQ=