Quality Products for Mechanical & Fluid Power 08 22 GEAR PUMPS ALPC/GHPC (short multiple) series gear pumps
® patented Elika profile is everything 01737 767493 info@jbj.co.uk www.jbj.co.uk - registered in England No: 1185469 - jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/E requirements You Tube www.jbj.co.uk/ .html pumps motors and Gear pump high pressure, teflon shaft seal can bear over-pressures of over 210 bar. A system of radial sealing at the shaft that can bear enormous internal over-pressures without resulting in damage. This radial sealing is particularly useful in single direction hydraulic motors when, in certain conditions of use, high over-pressures will be generated at the motor output. With bi-directional motors, the area adjacent to the seal ring of the drive-shaft is maintained at atmospheric pressure by the drainage circuit. In single-direction motors, this area is directly connected to the output so any over-pressure impacts directly on the seal ring, causing the lip to turn over or the ring to be expelled from its seat with a consequent leakage of fluid. The Teflon (P450) material adapts evenly to the texture of the machining on the shaft to guarantee a perfect seal. Reduce noise levels by an average of 15 dBA. Including group 2, 3 and multiple pumps. The helical profile of the gears reduces pressure oscillations and vibrations produced by the pump and transmitted to the other components, reducing the noise of the hydraulic system. Axial forces induced by the helical teeth are optimally balanced in all operating conditions by the axial compensation system integrated in the pump cover. Specific compensation areas into flange and cover, insulated by special gaskets reinforced with anti-extrusion, allow for fully free axial and radial movement of the bushings, which is proportional to pump operating pressure. In this way, internal leakage is dramatically reduced, ensuring very good volumetric and mechanical pump performances, as well as proper lubrication of pump’smoving parts. FEA of teflon high pressure seal Low noise, low pulsation helical gear pumps in group II, III & multiple formats The package consists of a bellhousing and flexible drive coupling that are fully machined to suit the pump and any driving interface; diesel or petrol engine, electric or hydraulic motor. jbj's in-house design team and manufacturing facility provide tailored solutions for your applications at competitive prices with quick delivery. A range of composite bellhousings to accommodate electric motor flanges from 300 mm diameter to 800 mm diameter. See pages 40 to 44 of the Pump Drive Components technical specification catalogue. Acollection of different ways of connecting hydraulic pumps andmotors to various driver devices. Allow close coupling of hydraulic pumps directly to the flywheel / flywheel housing of diesel engines, electric and hydraulic motors. www.jbj.co.uk/hydraulic-adaptors.html an excellence in engineering
ALPC/GHPC Contents quality products for mechanical & fuid power www.jbj.co.uk/gear-pumps.html #DriveLineHarmony Page Full range of gear pumps and motors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 5 ALPC1/GHPC1series........................................................................... 6 ALPC2/GHPC2series........................................................................... 7 ALPC/GHPC short multiple gear pumps ordering codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Technicalfeatures.............................................................................. 9 FTPGearPumpsforfluidtransfer ................................................................. 11 Getting the most out of your machinery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 #DriveLineHarmony............................................................................ 14 The details contained within this catalogue are reproduced in accordance with the latest information at publication of this catalogue. Errors and Omissions Excepted Last update: 31/08/2022
www.jbj.co.uk/gear-pumps.html #DriveLineHarmony 4
GHM Series Gear Motors The GHM series offer identical configurations to the ALM series but more robust thanks to the cast iron front flange and rear cover. ALM Series Gear Motors For medium to high pressure rates the ALM series is ideal for mobile and industrial sectors. Mono-directional and bi-directional with internal and external drain available. ALPC/GHPC Series Short Multiple Gear Pumps For reduced axial layout. Available with both flanges and covers in aluminium or cast iron. High production rates, performance consistency and absolute reliability ensure this a benchmark product for the hydraulic power pack market. 1P Series Gear Pumps Extensive range and very high performance of these pumps integrated in to micro power packs make them ideal for many applications from aerospace to marine, medical to automotive. 0.25 - 0.5 Series Micro Gear Pumps This product range includes pumps of displacements (up to 200cc/rev) in a full aluminium configuration, able to withstand medium to high pressures and using different versions of flanges (European, German and SAE), porting and shafts. Mono-directional as well as reversible. ALP Series Gear Pumps The GHP series offer identical configurations to theALP series and guarantees extreme reliability in very high pressure applications. Ideal for mobile applications from agricultural to construction machines as the cast iron allows more flange, cover and port options. GHP Series Gear Pumps Modularity and flexibility are the characteristics of these pumps. They allow the assembly of pump modules of the ALP and GHP (from 0.25 to 4) enabling solutions to a wide range of application requirements. Ideal pump for applications which require a fast approach and/or return of the actuator at low loads and slow motion of the actuator at high loads. e.g. log splitters, compactors & presses. Volumetric andmechanical efficiencies as well as low noise levels are further benefits of this range. High/Low 2-Pass Gear Pumps ALP/GHP Series Multiple Modular Gear Pumps ELIKA® The low noise, low pulsation helical gear pump. Groups 2, 3, 4 and multiple pumps. Reduces the noise level by up to 20 dBA. www.jbj.co.uk/gear-pumps.html #DriveLineHarmony 01737 767493 info@jbj.co.uk www.jbj.co.uk - registered in England No: 1185469 - jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/E requirements jbj Techniques Limited, UK distributor for www.jbj.co.uk/ .html gear-pumps 5
These particular multiple pumps, featuring a short overall length, can be supplied in both versions with two and three elements; they can be supplied with different configuration of flanges, shafts, inlet and outlet ports. It is also available a common inlet version with only one port feeding two or three elements. For information about combination of size, possible configurations and relative working conditions, please contact jbj Techniques Limited, telephone: 01737 767493 or email: info@jbj.co.uk www.jbj.co.uk/gear-pumps.html #DriveLineHarmony 6 ALPC1/GHPC1 Short Multiple Gear Pumps ALPC1/GHPC1 Series Front Element Rear Element Size Displacement Dimensions Size Displacement Dimensions cm3/rev MA (mm) LA (mm) cm3/rev MA (mm) LA (mm) ALPC1/GHPC1-...-2 1,4 58 32,5 ...-2 4,5 46,5 19 ALPC1/GHPC1-...-3 2,1 60 33,5 ...-3 6,4 48,5 20 ALPC1/GHPC1-...-4 2,8 62 34,5 ...-4 7 50,5 21 ALPC1/GHPC1-...-5 3,5 64 35,5 ...-5 8,3 52,5 22 ALPC1/GHPC1-...-6 4,1 66 36,5 ...-6 9,6 54,5 23 ALPC1/GHPC1-...-7 5,2 69 38 ...-7 11,5 57,5 24,5 ALPC1/GHPC1-...-9 6,2 72 39,5 ...-9 14,1 60,5 26 ALPC1/GHPC1-...-11 7,6 76 41,5 ...-11 16 64,5 28 ALPC1/GHPC1-...-13 9,3 81 44 ...-13 17,9 69,5 30,5 ALPC1/GHPC1-...-16 11 86 46,5 ...-16 21,1 74,5 33 ALPC1/GHPC1-...-20 13,8 94 50,5 ...-20 23,7 82,5 37
These particular multiple pumps, featuring a short overall length, can be supplied in both versions with two and three elements; they can be supplied with different configuration of flanges, shafts, inlet and outlet ports. It is also available a common inlet version with only one port feeding two or three elements. For information about combination of size, possible configurations and relative working conditions, please contact jbj Techniques Limited, telephone: 01737 767493 or email: info@jbj.co.uk www.jbj.co.uk/gear-pumps.html #DriveLineHarmony 7 ALPC2/GHPC2 Short Multiple Gear Pumps ALPC2/GHPC2 Series Front Element Rear Element Type Displacement Dimensions Type Displacement Dimensions cm3/rev MA (mm) LA (mm) cm3/rev MA (mm) LA (mm) ALPC1/GHPC2-...-6 4,5 70 38,5 ...-6 4,5 57 23,5 ALPC1/GHPC2-...-9 6,4 73 40 ...-9 6,4 60 25 ALPC1/GHPC2-...-10 7 74 40,5 ...-10 7 61 25,5 ALPC1/GHPC2-...-12 8,3 76 41,5 ...-12 8,3 63 26,5 ALPC1/GHPC2-...-13 9,6 78 42,5 ...-13 9,6 65 27,5 ALPC1/GHPC2-...-16 11,5 81 44 ...-16 11,5 68 29 ALPC1/GHPC2-...-20 14,1 85 46 ...-20 14,1 72 31 ALPC1/GHPC2-...-22 16 88 47,5 ...-22 16 75 32,5 ALPC1/GHPC2-...-25 17,9 91 49 ...-25 17,9 78 34 ALPC1/GHPC2-...-30 21,1 96 51,5 ...-30 21,1 83 36,5 ALPC1/GHPC2-...-34 23,7 100 53,5 ...-34 23,7 87 38,5 ALPC1/GHPC2-...-37 25,5 103 55 ...-37 25,5 90 40 ALPC1/GHPC2-...-40 28,2 107 57 ...-40 28,2 94 42 ALPC1/GHPC2-...-50 35,2 118 62,5 ...-50 35,2 105 47,5
Type Rotation Front (1) Middle (2) Rear (3) Shaft Front (1) Middle (2) Rear (3) Seals Options GHPC1 European Rectangular Flange Standard Flange SAE 50-2 (A-A) Standard Flange SAE 82-2 (A) Clockwise Counter Clockwise D S A A2 2 3 4 5 6 7 9 11 13 16 20 Tapered 1:8 T0 Straight Ø 12 mm C0 Tang 5 mm G0 Straight Ø 1/2 inch C1 Splined ANSI TH.9 S1 Straight Ø 5/8 inch C3 Splined ANSI TH.9 S1 Flanged at 4 threads E Cylindrical gas thread FG Conical gas thread FC UNF thread FA omit -10°C +80°C -10°C +120°C -40°C +120°C -40°C +80°C omit V ST H Reinforced shaft seal TR Common inlet Ac123* * list of elements with common inlet; select as first the one where the inlet port is located. Examples GHPC1-D-5/5-T0-E = double pump, clockwise rotation, 3.5+3.5 cm³/rev, configurated as in the drawing. GHPC1A-D-5/5/5-S1-FA-AC23 = triple pump, clockwise rotation, 3.5+3.5+3.5 cm³/rev, splined shaft S1, common inlet AC between middle and rear element located on the middle element. } Size } ALPC/GHPC Short Multiple Gear Pumps Ordering Codes Ports Type Rotation Front (1) Middle (2) Rear (3) Shaft Front (1) Middle (2) Rear (3) Seals Options GHPC2 European Rectangular Flange Standard Flange SAE 82-2 (A-A) German Rectangular Flange Clockwise Counter Clockwise D S A BK1 6 9 10 12 13 16 20 22 25 30 34 Tapered 1:8 T0 Straight Ø 15 mm C0 Splined DIN S0 Straight Ø 5/8 inch C1 Splined ANSI TH.9 S1 Straight Ø 3/4 inch C2 Splined ANSI TH.11 S2 Flanged at 4 threads E Flanged at 4 threads EP Cylindrical gas thread FG Conical gas thread FC omit -10°C +80°C -10°C +120°C -40°C +120°C -40°C +80°C omit V ST H Reinforced shaft seal TR Common inlet AC123* * list of elements with common inlet; select as first the one where the inlet port is located. } Size } Ports 37 40 50 UNF thread FA German Rectangular Flange BK2 /4 /7 Tapered 1:5 T1 Splined DIN5482 S3 Tapered 1:5 T2 Diagonal flanged at 4 threads D Tang 8mm G0 Examples GHPC2-D-16/16-T0-E = double pump, clockwise rotation, 11.5+11.5 cm³/rev, configurated as in the drawing. GHPC2A-D-16/16/16-S1-FA-AC32 = triple pump, clockwise rotation, 11.5+11.5+11.5 cm³/rev, splined shaft S1, common inlet AC between middle and rear element located on the rear element. www.jbj.co.uk/gear-pumps.html #DriveLineHarmony 8 GHPC1 GHPC2
ALPC/GHPC Short Multiple Gear Pumps Short Multiple Pumps ALPC1 and GHPC1 are special type of two stages and three stages multiple pumps with reduced axial length. Upon request and after verification of the functioning cycle and operating conditions those pumps can be eventually provided with more than three stages. ALPC1 are pumps with diecast flange and cover. GHPC1 are pumps with cast iron flange and cover. A special common inlet version with just one inlet port feeding two or three elements is also available. Contact jbj Techniques Limited, technical office, telephone: 01737 767493 or email: info@jbj.co.uk for further information regarding different possible configurations, displacements and relative operating conditions. Technical features 3 3 Displacement: from 1.4 cm /rev. to 13.8 cm /rev. ~ Maximum pressures refer to 1P-ALP-GHP catalogue rpm pump range: from 1,000 rpm to 4,000 rpm Ports: Common inlet (option) ~ Side ports code E, FG, FC, FA. Flanges and shafts: As 1P, ALP1, ALP1AQ models refer to 1P-ALP-GHP catalogue ALPC2 and GHPC2 are special type of two stages and three stages multiple pumps with reduced axial length. Upon request and after verification of the functioning cycle and operating conditions those pumps can be eventually provided with more than three stages. ALPC2 are pumps with diecast flange and cover. GHPC2 are pumps with cast iron flange and cover. A special common inlet version with just one inlet port feeding two or three elements is also available. Contact jbj Techniques Limited, technical office, telephone: 01737 767493 or email: info@jbj.co.uk for further information regarding different possible configurations, displacements and relative operating conditions. Technical features 3 3 Displacement: from 4.5 cm /rev. to 35.2 cm /rev. ~ Maximum pressures refer to ALP-GHP catalogue rpm pump range: from 1,000 rpm to 4,000 rpm Ports: Common inlet (option) ~ Side ports code E, EP, FG, FC, FA, D, rear ports KA Flanges and shafts: As ALP2, ALP2A, ALP2BK models refer to ALP-GHP catalogue ALPC3 and GHPC3 are special type of two stages and three stages multiple pumps with reduced axial length. Upon request and after verification of the functioning cycle and operating conditions those pumps can be eventually provided with more than three stages. ALPC3 are pumps with diecast flange and cover. GHPC3 are pumps with cast iron flange and cover. A special common inlet version with just one inlet port feeding two or three elements is also available. Contact jbj Techniques Limited, technical office, telephone: 01737 767493 or email: info@jbj.co.uk for further information regarding different possible configurations, displacements and relative operating conditions. Technical features 3 3 Displacement: from 20 cm /rev. to 87 cm /rev. ~ Maximum pressures refer to ALP-GHP catalogue Continuous max. pressure: refer to ALP-GHP catalogues rpm pump range: from 1,000 rpm to 4,000 rpm Ports: Common inlet (option) ~ Side ports code E, EP, FG, FC, FA, A, D. Flanges and shafts: As A, A2,BK1,5 refer to ALP-GHP catalogues www.jbj.co.uk/gear-pumps.html #DriveLineHarmony 9
An experienced and dedicated teamof technical sales engineers are on hand to work with customers and deliver results. The markets where jbj operate are tough and time sensitive. In such circumstances customers need reliable solution partners, people who are conscious of deadlines, innovative in design and always willing to seek the best solution for the customers' needs. On all counts, jbj Techniques Limited deliver. From specification, through technical advice, manufacture and support, together with our extensive product database, jbj Techniques provide a comprehensive and valued service to the power transmission and hydraulic industries. jbj Techniques Ltd provide a diverse range of mechanical drive & transmission solutions to industrial markets including design engineering, product supply and after sales service. www.jbj.co.uk/Marzocchigearpumps.html integrated valves and mounting arrangements ALP/GHP . . . . VP-LS: Load sensing pump with priority valve. ALM . . . . VN - VM: Motors with anti-cavitation valves and relief valve. ALM . . . . VE: Motor with proportional relief valve. ALP/GHP . . . . T: Pumps with support bearing for high side/radial loads. ALP . . . . VM: Pump with integrated relief valve. ALM/GHM . . . . T: Motors with support bearings for high side/radial loads. Hydraulic Gear Pumps Standard Gear Pumps #DriveLineHarmony www.jbj.co.uk/gear-pumps.html
an excellence in engineering www.jbj.co.uk/ .html FTP-gear-pumps Marzocchi FTP pumps are based on ELIKA Gear Technology that reduces the noise level by an average of 15 dBA compared with a conventional external gear pump. The helical gears ensure the continuity of motion despite the low number of teeth. FTP pumps are perfectly interchangeable with standard gear pumps. The low number of teeth reduces the fundamental frequencies of the pump noise, therefore lowering sound levels. The shape of the Elika profile, patented by Marzocchi Pompe, eliminates the encapsulation phenomenon typical of standard gear pumps, remedying the source of themain cause of noise and vibrations. By reducing the pressure-oscillations and vibrations produced by the pump and transmitted to the other components, the noise of the hydraulic system itself is reduced. Specific compensation areas in the flange and cover, insulated by special gaskets reinforced with anti-extrusion, allow for fully free axial and radial movement of the bushings. Ideal for low-pressure, low viscosity, lubrication applications such as fire-resistant fluids. The FTP gear pump fromMarzocchi is an ideal solution for low-pressure lubrication applications where low-viscosity fluids are required, such as fireresistant fluids. Typical applications include large lubrication systems, lubrication of the guides of machine tools, and the lubrication and cooling of tools themselves. Fire-resistant fluids are used whenever there is a possibility that a hydraulic fluid (also used for lubrication) may encounter a source of ignition, such as the surface of very hot equipment. Fire-resistant hydraulic fluids are specially formulated so they are more difficult to ignite and do not propagate a flame froman ignition source. There are several types of fire-resistant fluids and they are generally classified as follows: oil and water emulsions, water-polymer solutions, and anhydrous synthetics. More specifically, the International Standards Organization (ISO) further classifies these fluids as follows: HFAE – oil-in-water emulsions, typically with more than 80%water content; HFAS – synthetic aqueous fluids, typically with more than 80%water content; HFB – water-inoil emulsions, typically with more than 40%water content; HFC – water polymer solutions, typically with more than 35%water content (also known as glycol solutions, polyalkylene glycol solutions or water glycols); HFDR – synthetic anhydrous fluids composed of phosphate esters; and HFDU – synthetic anhydrous fluids other than phosphate esters. Examples include polyol esters and polyalkylene glycols. The only fire-resistant fluids that are completely incompatible with gear pumps are the HFDR ones; for all the others, it is possible to obtain a configuration that makes them compatible. To avoid fast wear of the sliding contact parts, FTP pumps can be supplied, depending on the type of application with bronze or bronze/PTFE thrust plates. These FTP helical gear pumps are available in versions with or without a relief valve built into the cover, and maximum working pressure is 50 bar. The gear pumps have very high specifications for rotation speed and viscosity range. FTPpumps are available in clockwise rotation whilst a counter-clockwise rotation version is currently under development. www.jbj.co.uk/ftp-gear-pumps.html
Getting the most out of your machinery often depends on close integration between all components. An organisation that manufactures and integrates all the diverse components of a drivetrain provides the experience to help you select the best component combination for your application. jbj Techniques’ in-house design team and manufacturing facility provide tailored solutions for your applications at competitive prices with quick delivery. The following examples are a simplistic view of how jbj Techniques assists customers. Hydraulic Adaptors Designed primarily to allow the close coupling of hydraulic pumps to a variety of prime movers, such as diesel / petrol engines, electric, air or hydraulic motors, they can also be used in the connection from prime mover to alternative driven parts i.e. gear boxes, generators, water or vacuum pumps etc. An additional range of engine front PTO adaptors, which provide additional connection between the engine pulley and the driven part are also available. The kit comprises of a and flexible bellhousing drive that are fully machined to suit the coupling driving and driven components. These can be to suit either shaft to shaft, flange (flywheel) to shaft or even flange to flange connections. Getting the most out of your equipment will demand close integration between all components. In specifying jbj Techniques as your preferred supplier, you will have selected a company with the experience to specify, manufacture and integrate all of the diverse components that will ensure the best component combination for your application. jbj's in house design team and manufacturing facility provide tailored solutions for your applications at competitive pricing and on-time deliveries. Pump shaft alignment is key to preventing unnecessary wear and damage to the pump shaft seal and bearing. Improper alignment may lead to premature pump failure. Also to be considered are unwanted torsional resonant frequencies in the system which can quickly cause damage to components in the drivetrain and reduce system life and performance. Improper pump installation can lead to premature failure, increased maintenance costs and reduced production levels of final product. jbj Techniques can advise on the correct installation of into Industrial / hydraulic pumps mobile / marine / machine tool / agricultural / offshore industries and can specify complete driveline systems from their extensive range of components which are available from stock or manufactured to order, albeit simple or complex, standard or bespoke. Electric Motor – Hydraulic Pump Adaptors (safe area) jbj Techniques Limited offer the most comprehensive range of in Europe. bellhousings Designed to connect electric motors with frame size IEC D56 - D400 (0.06kW – 750kW) and can be compatible with electric motor 'B5' or 'B14' flange configurations. Accompanying the metric frame units above is a complete range of mountings to suit Nema and imperial frame motors with 'C' face or 'D' flange fitments. With fully machined , torsionally flexible couplings or available, jbj ensure torsionally rigid couplings the most suitable combination is selected for the application in hand. As an example spider couplings are available in various materials including aluminium, grey cast iron, nodular iron, steel and stainless steels and can be finish machined with parallel, taper or splined bores to DIN, SAE, ANSI or ISO standards. Bellhousings can be manufactured in aluminium or cast iron material as standard, however, units can be produced in a variety of exotic materials on request. The aluminium product range is produced in either monoblock or composite formats giving great flexibility in design and allows for early delivery time, often with same or next day delivery possibilities. For applications where low noise levels are a quality products for mechanical & fluid power #DriveLineHarmony www.jbj.co.uk an excellence in engineering
ensuring a continuing high quality service in which customers can have complete confidence. “ “ requirement then a complete range of antivibration and noise reduction components add to the range. Electric motor – Hydraulic Pump Adaptors (hazardous area) Designed to meet the exacting safety standards of the offshore and chemical process industries, jbj Techniques produce certificated to adaptor kits Directive 2014/34/EU II2GD-IM2-TX -50 C< Service Temp < +105 C. Harmonised standards BS EN 1127:1, BS EN 13463:1, BS EN13463:5, BS EN 50303, BS EN 1834-1,BS EN 1834-3. Generally manufactured in Cast or Nodular iron, bellhousings can be produced in steel, stainless steel or alternative exotic materials on customer request. Couplings supplied for these applications are the jbj Techniques 'JXL' pin and bush range which provide an anti-static and flameproof drive which meet zone 1 area requirements, conforming to all of the above standards. Also available are spider and gear couplings which are certified to zone 2 standards. (Contact jbj Techniques for details). An important development of equipment for use within hazardous areas is the wet mount series of bellhousings. Commissioned to research and develop a product that would control the high temperature generated by a piston pump shaft seal when working within cycling applications. A little considered issue is the frictional heat generated at the shaft seal when the application requires the pump to cycle between different pressures causing the seal temperature to increase. This process will often take the seal temperature out and above the levels required by the relevant ATEX standards requirement. This specially designed assembly allows a pumped cooling flow to be passed over the seal face and through an auxiliary cooler, this in turn reduces the seal face temperature which can be maintained at an acceptable level. With a vast array of components to select from, jbj are well placed to provide all required components to support the required cooling system. Diesel Engine – Hydraulic Pump Adaptors A complete range of bellhousing and couplings exist for the connection of a diesel engine flywheel to a specified driven component, be it an oil hydraulic pump, water pump, generator or similar device. With the bellhousing available in various materials to suit all application areas. With a standard range to connect Diesel engines with SAE dimensions from SAE '6' to SAE '0' jbj are well placed to satisfy the majority of customer requirements. Couplings to complete the assembly are available in either torsionally flexible or torsionally rigid design ad can be supplied to suit SAE flywheel dimensions from SAE 6.5” to SAE 18”. For hydraulic pumps to be mounted to engines that do not conform to SAE dimensions, we offer a full range of assembly parts, some of which (but not all) are shown here » for diesel engines All bellhousings within this range can be finished machined to accept any, piston, vane or gear pump interfaces requested by customer. As with the electric motor range of product jbj offer complete solutions for ATEX environments, using our well proven 'JXL' coupling range which has standard design to connect to the engine flywheel. Directive 2014/34/EU II2GD-IM2-TX -50°C ≤ Service Temp ≤ +105°C. Harmonised Standards: BS EN 1127:1 BS EN 13463:1 BS EN 13463:5 BS EN 50303. Petrol Engine – Hydraulic Pump Adaptors Petrol engine adaptors have been developed for use with industrial petrol engines. Design exists to suit Honda, Briggs and Stratton, Kawasaki, Kubota, Hatz, Mag, Robin, Suzuki, Winsconsin, to name but a few, all adaptors can be finished to accept most hydraulic pumps. Adaptors to suit engine crankshaft drives and for vertical mounting are available on request. #DriveLineHarmony www.jbj.co.ukl to Large Combinations Small Individual Components
to Large Combinations from Small Individual Components ensuring a continuing high quality service in which customers can have complete confidence. “ “ # Driveline jbj Techniques is a specialist supplier of high-quality products for the mechanical power transmission and fluid power sectors. The company offers a high level of in-house expertise plus a huge selection of products to meet a very broad range of customer applications. From specification, through technical advice and manufacture to after-sales support, jbj Techniques provides a comprehensive and valued service to the power transmission and hydraulics industries. The company fields a UK-wide team of technical sales engineers to ensure that the business is close to its customers, and it enjoys excellent associations with European manufacturers, acting as sole UK distributor in many cases. jbj’s team is recognised for its expertise in the selection and configuration of hydraulic and mechanical transmission systems. Able to draw on an that extensive product range provides the building blocks for bespoke systems both large and small, the in-house design team offers a complete service, ranging from an assessment of customer requirements to full technical backup, including product specification, CAD based system design, system build and certification. Moreover customers can take advantage of jbj’s own machine-shop facilities and skilled engineers guarantee to quality and control costs. jbj Techniques provides one of the widest ranges of couplings available within the UK; mechanical power transmission couplings for a vast range of applications. Ranging from miniature couplings, all steel gear couplings, flexible spider couplings, shaft couplings, torque limiting couplings, disc and grid type couplings, ATEX compliant and shaft locking devices. Magnetic couplings for power transmission between hermetically sealed areas. However as extensive as the selection is, couplings make up a fraction of jbj’s portfolio. As power transmission specialists the company stock and provide gearboxes, clutches, pumps, hydraulic motors, flow meters, fluid power accessories including: cooling & heat exchange products, reservoirs, pipe flanges, seals and level indicators, as well as a variety of bellhousings and engine adaptors, to name just a few of the product categories. jbj Techniques Limited is proud of it’s relationship and reputation with customers and suppliers. The core client base is stable and loyal, which is testament to the quality of service provided by the company. A similar relationship exists with suppliers, ensuring a continuing high quality service in which customers can have complete confidence. Dampers Engine Adaptor Kits Hydraulic Adaptors Torque Limiting Couplings Tyre Couplings Anti-static/Flameproof Couplings Torsionally Rigid Couplings Torsionally Flexible Couplings Bellhousings Permanent Magnetic Couplings Torsional Couplings
ne Harmony comprehensive range of components www.jbj.co.uk an excellence in engineering 01737 767493 info@jbj.co.uk www.jbj.co.uk - registered in England No: 1185469 - jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/E requirements Screw Pumps Pneumatic Motors & Starters Gear Pumps/Motors Axial & Radial Piston Motors Vane Pumps LSHT Motors/Geared Motors Splitter Gearboxes Planetary Gearboxes BDS Clutches BD Clutches & Gearboxes Oil Bath Clutches Flow Dividers Tanks/Accessories Fluid Level Indicators Flanges Mini Power Packs Coolers Pressure Intensifiers You Tube
jbj Techniques Limited 28 Trowers Way Holmethorpe Industrial Estate Redhill Surrey RH1 2LW. UNITED KINGDOM 01737 767493 info@jbj.co.uk www.jbj.co.uk quality products for mechanical & fluid power registered in England No: 1185469 jbj Techniques Limited is ISO certificated, committed to international coordination & unification of industrial standards. A range of products ATEX certificated to directive 94/9/EC requirements UK distributor You Tube
RkJQdWJsaXNoZXIy NzQyNjQ=